How to replace the oil filter on a Toyota Corolla yourself

How to replace the Toyota Corolla oil filter?

According to the recommendations of professionals, replacing the oil filter and engine lubrication on a Toyota Corolla is recommended every 10 thousand kilometers. Some people prefer to trust all service work to service station specialists, but many car enthusiasts cope well with such procedures on their own.

New oil filter element for Toyota Corolla

Before replacing, you need to purchase a good oil filter. There is no need to save money here; it is better to make a purchase in a specialized store and take the best one, even if you have to overpay a little. Moreover, the difference will not be too big.

Where is?

Replacing the oil filter on a Toyota Corolla is a simple process, since the filter is located in an accessible place - under the bottom of the car. And to replace it, you do not need to remove additional systems.

Step-by-step replacement instructions

It is better to carry out all work on a lift or overpass, but if this is not possible, then an ordinary inspection hole, which is found in virtually any garage, will do. If motor protection is provided, it must be removed. In this case, it is not necessary to completely unscrew the bolts, but simply pull them forward a little.

What will you need?

Screwdriver Set;
special key for removing the barrier;
funnel;
a set of keys;
new lubricant;
rags;
container for draining waste.

Stages

Use a screwdriver to remove the rubber plugs in the motor. We first place a container under the drain hole to drain the waste liquid.
Using a wrench, unscrew the oil drain plug.
Unscrew the drain plug
We drain the waste.
Drain the old oil
We tighten the plug.
Press out the protective plate.
Protective plate
We unscrew the cap with the old filter using a special key. This must be done carefully.
Unscrewing the cap
Let's take it off.
Removing the old element
Replace the O-ring after lubricating it with oil.
Pour a little oil into the new filter, a little more than half.
Pouring oil into a new element
Install it in place of the old one.
Putting up a new barrier
Place the locking protection plate in the position it was in before.
Fill in new oil.
We start the engine and let it run for a while.
Checking the level.
If there is a shortage, add more and vice versa.

Many experts advise washing the car engine at the same time when changing. But this procedure is not necessary if you use high-quality consumables and carry out all service work on time.

Video “Installing a new oil barrier”

This video shows in detail the process of changing the oil filter on a Toyota Corolla.

Source: https://labavto.com/toyota/corolla/zamena-maslofiltra/

Changing the oil and oil filter Toyota Corolla 2010-2014

The oil filter and oil are changed every 10,000 km; the replacement date may vary slightly depending on specific operating conditions.

This article provides an example of an oil change for Toyota Corolla cars from 2010.

From 2006 to 2010, all operations are similar, except that the design uses a classic oil filter in a metal housing instead of a filter insert.

To remove and install the oil filter on a Toyota Corolla, you will need the following tools: a 14 mm socket, a wrench for the oil insert cap code 09228-06501 or a chain or soft oil filter puller with a strap, a funnel, a screwdriver.

Using a screwdriver, remove the rubber plugs from where they fit in the engine protection

Unscrew the oil filler plug in the engine compartment

Using a 14 mm wrench, unscrew the plug from the crankcase to drain the oil.

We drain the oil into a volume of at least 4.2 liters, this is exactly the volume of oil in the crankcase of a Toyota Corolla 2006-2012 year of manufacture 1.6 liter engine 1 ZR-FE

Use a special key 09228-06501 to unscrew the cap. The cap can also be unscrewed with a strap wrench or a chain wrench. When unscrewing with a chain wrench, it is necessary to wrap the chain in a strip of rag so as not to damage or leave marks on the plastic cap. I filmed it exactly like this.

We take out the cap with the filter element.

We take out the filter element

Instead of the installed original Toyota filter element code 04152-37010, an analogue of Knecht (Mahle Filter) OX 416 D1 was installed

Place of landing of the filter insert. It is worth noting that the metal cartridge is spring-loaded, ensuring that the replacement cartridge is pressed against the sealing surfaces

View of the filter insert cap. Inscriptions: screw clockwise, unscrew counterclockwise. tightening torque 25 N*m, that is, 2.55 kg per meter.

Six threads, that is, six turns until fully tightened. A rubber sealing ring (circular cross-section) is installed on the cap. If the ring is in good condition without nicks or nicks, then there is little point in changing it. The new filter comes with a new ring. If necessary, replace and lubricate with oil.

We install a new filter element.

Add oil. The oil is absorbed into the porous surface, so once it has been absorbed, add more oil. This is necessary so that in the first seconds of starting the engine, oil immediately begins to flow to the valves through the cardboard, and does not linger in the chamber of the replaceable insert.

We install the cap with the filter insert in place.

Pay attention to the location of the cap. It must reach its position before removal. There are marks on the cap between which there should be a pointer - you can see in the photo opposite the number 10 on the tape measure.

Fill the oil through the oil filler neck. We wrap the cork.

The oil should be between the level marks. After the first trip, check the engine oil level and top up if necessary.

I would also like to separately highlight the option of express oil change in a car engine; more detailed information about the technology of operations and the features of such a change can be found in the article “Express engine oil change”

Source: http://www.AutoSecret.net/dvigatel-toyota-corolla/1080-zamena-masla-i-masljannogo-filtra-toyota

Changing the oil on a Toyota Corolla - step-by-step instructions!

Oil change for Toyota Corolla

Some services are dishonest and cheat on such an important procedure as changing the oil. Are you sure that what they promise will be poured into your engine? You can request your presence during the replacement, but this is not always possible. Why not change the oil yourself?

The interval at which the oil on Corollas should be changed is 10,000 kilometers. The oil filter is also changed at the same interval. The first change is after 5000. The first oil I had after five thousand was dark. Either this is poured at the factory, or it is the result of grinding in the engine mechanisms.

The type of filters installed in cars produced before 2010 differs from those that began to be used after: the traditional one with a metal body was replaced by a filter insert.

The insert, you need to understand, is cheaper, but replacing it is more difficult.

The traditional filter is dismantled using a 14 key, the insert is changed using a special device - a key with catalog number 09228-06501.

Using the same 14 key, unscrew the plug from the drain hole. Drain the oil. In a standard 1.6 engine there is more than 4 liters, 4.2 to be precise. If the engine in the car did not eat up, so much will come out. We change the one-piece filter or insert. Be careful with the insert - the plastic housing-cap is afraid of scratches, so if you don’t have the key 09228-06501, put a rag under the traditional chain key.

Instead of the original filter element, you can use Mahle. It’s not worth saving on oil, and Makhovsky filters are no worse than original ones at one and a half times lower price.

What kind of oil should I use? It’s better not to skimp here and pour Toyota 5W-40. Pour cheaply at your own peril and risk.

We clean all surfaces from old oil and dirt. There is no need for dirt in the engine. Pour 4.2 liters of synthetic into the filler neck, add another 150 grams, since the level will drop a little when the car is running.

We tighten the plug. Pour a little oil into the filter element, so much so that it is slightly above the level of the porous body of the insert. We install new gaskets, place the insert in its socket and screw it on.

Step-by-step photo report on changing the oil on a Toyota Corolla

Open the cover on the engine protection. Unscrew the bolts on the engine protection. Open the engine cover. Drain the used oil. Fill in new oil. Check the oil level.

Video - step-by-step technology for changing oil on Toyota Corolla

Source: https://filtrzamena.ru/zamena-masla-na-toyota-korolla.html

Do-it-yourself oil change in a Toyota Corolla engine

In today's material we will talk about the essentials. The road history of any car owner includes an episode of changing the engine oil. We address this article to the happy owners of the Toyota Corolla. We will try to explain all the nuances related to this issue in an accessible form. So, how to change the oil in your car’s engine with your own hands ?

Careful preparatory work will ensure an easy and quick oil change. Start by purchasing the necessary supplies. You will need:

Engine oil for Toyota Corolla;
Funnel;
Key for oil insert cap;
Screwdriver;
14mm head;
Oil filter puller.

To yourself , leave the car running to allow the engine to warm up thoroughly. This will give the oil a more fluid consistency. A step-by-step guide developed by experts will simplify this procedure as much as possible. Just follow it and do everything slowly.

The first step is to remove the used oil. This is done as follows:

Remove the rubber plugs;

Remove the oil filler plug using a wrench;

Using a key wrapped in a cloth, remove the cap along with the filter;
Drain the oil.

Pay attention to the rubber seal. In some cases it should also be updated.

Then you can start adding fresh oil. We recommend using original Japanese Tayota oils. They work ideally on original cars, allowing you to reduce the amount of fuel consumed.

The manufacturer also took care of such composition indicators as resistance to critical temperatures. Your car will work smoothly even in hot and cold weather.

If your car has a fairly long period of active use, it would be a good idea to carry out the procedure of flushing the engine with special flushing oil. Otherwise, this sequence of actions will suit you:

Fill the oil to the required level;

Replace the filter with a genuine Tayota part, following the factory recommendations on the filter insert;
Install the filter cap;
Close the container with a stopper.

Some of the oil may have been absorbed into the filter. After the first trip, check the oil level in the car. We hope that our instructions helped you save money and time. Be careful on the roads!

Video: Changing the oil at home. Toyota Corolla 2008

Source: http://avtozvuk.info/zamena-masla-v-dvigatele-tojota-korolla.html

Oil filter Toyota Corolla

Modern internal combustion engines of modern vehicles have many rubbing parts. To reduce power losses from friction, rolling and sliding bearings are used. The first type of bearings are lubricated with solid grease, while the second type requires liquid motor oil.

Modern high-speed Toyota Corolla engines require high-quality lubrication, as it also helps cool rubbing pairs, protects engine parts from corrosion, and helps remove wear products from rubbing parts and carbon deposits formed in the engine cylinders during operation.

An important element in this system is the oil filter. All solid particles remain in it, which are washed out by oil while the engine is running. The cleaner it is, the better for the Toyota Corolla engine.

What is an oil filter?

Its main purpose in the lubrication system is to clean the lubricating fluid from various types of solid particles, combustion products and other contaminants.

It is always based on the use of filter elements. When choosing them, the technical features of the material used, especially its quality, are taken into account.

The quality of the product being cleaned, as well as the operation of the entire lubrication system, entirely depends on their properties.

Disassembled oil filter

Today, in many countries, the production of oil filters for Toyota Corolla has been established. But the highest quality still remains with original parts from Japan. It is not for nothing that they are considered consumables, since after working for the allotted time, they must be replaced; their restoration for reuse is not provided.

For the manufacture of the filter element, only high-quality specially designed paper is used. It has a significant thickness, which allows it to retain solid particles from the engine oil. In the housing it is folded in such a way as to create the largest possible working area of the oil filter.

There is another feature by which it is easy to distinguish original oil filters - the presence of bypass valves in them. The bypass valve may allow engine oil to enter the system when the filter is not working.

Whereas its absence leads to engine accidents due to the lack of an oil film in the rubbing vapors. They just jam.

Original Toyota products also differ in the quality of the material used for the sealing gasket.

Why is lubrication system maintenance necessary?

Motor oils are produced in several types. They can be:

Mineral.
Semi-synthetic.
Synthetic.

During their production, they receive additives to improve properties and viscosity characteristics. After the time specified by the manufacturer, the engine oil must be replaced. Some additives lose their properties, some burn out. The color of the lubricant and oil filter indicates the impending replacement of the lubricant.

Toyota Corolla has been enjoying the reputation of a reliable car for a long time. Owners rarely have to deal with problems with this car. If you wish, you can learn and carry out maintenance of the lubrication system yourself.

Source: http://CorollaCar.ru/remont/dvigatel/maslyanyj-filtr-tojota-korolla.html

Replacing the Toyota Corolla oil filter

Changing the oil is a mandatory procedure after an impressive amount of time and a certain amount of mileage, approximately every 10,000 km. Why do you need space in a car? In order to reduce friction between certain parts, it also reduces the risk of wear of engine parts.

How and why the oil is changed

It is customary to carry out the oil change procedure when the engine is completely warmed up; this is necessary for good oil fluidity and easier drainage of waste from the engine.

You should know that it is necessary to avoid, if possible, burns caused by too hot oil when draining, and also avoid getting this oil on any exposed areas of the body. To avoid environmental degradation, it is not recommended to pour used oil down the drain.

Before you start changing the oil in your Corolla, you need to stock up on all the necessary tools so that you don’t have to look for them during this procedure.

Sometimes it is recommended to change the oil along with flushing the engine with special flushing oil. This will have a positive effect on every car, especially one that has already done significant mileage.

Thanks to such flushing, all contaminants are thoroughly removed from the most inaccessible places of the engine.

Undoubtedly, an important fact is to be careful and exercise caution when working, as the collector can be very hot.

Required Tools

To replace the oil filter on a Toyota Corolla, you need the following tools:

Key for 14
The key required to remove the oil filter (you can use a chain one)
Screwdriver
Oil
Funnel
The oil filter itself (original)

Replacing the oil filter

Filter replacement process:

To avoid engine wear, timely oil changes are necessary. The first step is to lift the car on a lift, and you can also drive it into a pit.
Now remove the rubber plugs from the engine, and then unscrew the plug from the pan in it.
You need to install the car on some horizontal platform and let it warm up, for the reason that the oil drains faster and takes with it the maximum amount of contaminants.
After the car has warmed up sufficiently, you need to stop the engine and use a 14 key to unscrew the drain plug on the cylinder head cover.
Next, very carefully, without touching the hot parts of the exhaust system, place the pan under the drain plug and unscrew it.
It is recommended to unscrew the drain plug using a spanner wrench while wearing gloves; this is necessary to avoid tearing off the edges of the plug.
Now you need to drain the oil into the pan that was placed earlier, since the Toyota Corolla engine capacity is 1.6 liters, the approximate volume of drained oil should be 4.2 liters. During the draining procedure, it is necessary to monitor the stream in order to have time to rearrange the vessel in time.
After the oil has drained, you need to wipe the stopper with a piece of rag. This is a necessity, since if the smallest parts remain, you will soon have to carry out the oil change procedure again due to contamination of the fresh one. Now tighten the plug.
Next, place a pan under the oil filter.
Remove all unnecessary tools and rags under the car without touching the oil pan.
Now, using a special wrench, unscrew the oil filter by turning it clockwise.
Remove the filter element together with the cap by hand.
Use a clean piece of rag to wipe the area where the filter was located on the cylinder block. Do not leave used oil in that place, as later, when the engine heats up, it will smoke.
Next, lubricate the rubber gasket of the new filter being installed with a thin layer of oil, and then screw the filter into its place.
Tighten the filter by hand rather than with a wrench, as this may damage the rubber gasket.
Now pour oil into the central part of the filter. This must be done through a funnel to avoid spilling it on the engine. Filling must be done gradually, for the reason that it is absorbed into the filter fibers.
Next, install the cap and filter element in place. It should be in the position it was in when twisted.
After the first trip, check the oil level; it may happen that it will need to be topped up.

Read also

Source: http://grandrepairauto.ru/zamena-maslyanogo-filtra-toyota-corolla.html

All about changing the oil in a Toyota Corolla engine

In principle, the process of replacing fluid in a Toyota Corolla engine is not particularly labor-intensive. The main thing is to know the basics in general and correctly perform all the steps described in the instructions in order to do everything correctly. So, let's consider in order all the questions that may interest you.

What MM should I use?

Toyota Corolla car

Of course, foreign-made vehicles must be well maintained in order to always be on the move. And Toyota Corolla is no exception. The engine of this car must be filled with only high-quality motor oil, which the manufacturer warns about in the service manual.

A high-quality liquid is nothing more than original engine oil for Toyota Corolla engines. It’s called “Toyota motor oil”. If the auto stores in your city do not have such consumables, then we can recommend that you purchase the liquid from an authorized dealer or place an order online.

Loading …

How much to pour?

Toyota Corolla engine volumes are about 4.2 liters, depending on the year of manufacture and configuration. But this question cannot be answered unequivocally. You should be guided by the amount of drained waste fluid in order to know exactly how much to pour into the engine of your car.

Or read the operating instructions for your vehicle. Usually in the manual the manufacturer indicates the volume of the internal combustion engine so that owners can figure out how much oil is needed. In any case, to calculate the most accurate volume, you will need a service book. But on average, Toyota Corolla engines contain at least 4.2 liters.

When should you change?

This question came to every Toyota Corolla owner. In principle, the terms for replacing the fluid here are the same as for other vehicles. On average, engine oil changes for a Toyota Corolla should be carried out at least 10 thousand kilometers.

If you are using low-quality consumables for the engine or feel that the engine is not working as well as before, then the replacement frequency can be reduced. Replacement can be carried out after 5 thousand kilometers.

Necessary tools

Before you start work, prepare:

set of wrenches;
Phillips screwdriver;
funnel.

Wrenches and sockets3. Long screwdriver Funnel with narrow neck

Step by step instructions

To change the engine oil, drive your Toyota Corolla onto a lift or into a garage with a pit.

Reach under the bottom and, using a screwdriver, remove the crankcase protection plugs from the motors.
Now open the hood and find the filler neck for consumables. Unscrew the lid and set it aside.
Then reach under the vehicle again and locate the drain plug. Place a container under it in which you will collect the “working off”, and unscrew the lid with a wrench.
Now you will have to wait a little while until all the used engine oil has left the system. As stated above, on average this volume is about 4.2 liters for 1.6-liter engines.
Next, it is necessary to dismantle the MM filter element. Before dismantling, remember its location. To do this, unscrew the plastic protective cap of the filter. If you cannot do this by hand, use a chain wrench or wrap a rag around the filter housing. In any case, even if you do this with a wrench, still wrap the protective housing of the filter component with a rag so as not to damage it. Remove the cap along with the protection, and then remove the filter component itself from the cap.
Replace the filter with a new original one. Also pay attention to the condition of the rubber seal that is installed on the protective housing. If it is in more or less adequate condition, then it makes no sense to change it. But the new filter component also comes with a new gasket. Therefore, if there is a need, then you need to replace it. Before mounting it on the body, the rubber band should be lubricated with a small amount of motor fluid.
Next, you should pour motor fluid into the filter. Please note: the consumable material will immediately begin to absorb into the porous surface. Accordingly, when the oil is absorbed, it will be necessary to add more liquid so that the cap is half full. This must be done so that in the first seconds after the motor is turned on, the consumable material reaches all valves without delay.
Then install the filter element in the housing at the mounting location and tighten it. In this case, the tightening torque must be at least 25 Nm.
Now let's proceed directly to pouring engine fluid into the system. Tighten the drain plug, which is located under the bottom, when the waste liquid stops flowing out of it. Before doing this, check the condition of the plug and, if necessary, replace its O-ring to avoid possible leaks of consumables.
Remember in what position the protective housing with the filter was before dismantling. It should be installed in the same way.
Now you need to add new oil. Pour only as much fluid into the system as comes out. Overfilling and underfilling are excluded. After filling, close the lid and check the liquid level using the dipstick marks. It should be at a level between the MIN and MAX marks. Turn on the engine and allow it to warm up to normal operating temperature. After this, check the level of consumables again and add more if necessary.

1. Put your Toyota Corolla on the handbrake and unscrew the drain plug under the bottom.2. Wait about 30 minutes until the system is completely logged out. Remember the volume.3. Dismantle the filter element with the plastic protective housing and pull it out.4. Install the new filter into the protective housing and pour some liquid into it. If necessary, change the gasket.5. Screw in the drain plug and pour in as much MM through the filler neck as came out of the system when draining.6. Check the level of the filled liquid using the dipstick. Warm up the car to operating temperature and check the level again.

Actually, this process is completed. Use only high-quality MM to avoid possible engine problems in the future. Do not buy too cheap consumables of unknown manufacture, this can be fraught. We hope the material presented will help you cope with this matter.

Video from Vyacheslav Viter “How to change motor fluid at home”

You can learn how to change engine consumables with your own hands from the video.

Source: http://AvtoZam.com/toyota/corolla/zamena-masla-v-dvigatele-samomu/

Changing the oil in a Toyota Corolla engine

Every car owner always takes care of his car, while trying to maintain both its presentable appearance and the performance of all units.

To achieve this goal, it is necessary to undergo regular technical inspections and promptly replace all working fluids. This includes changing the Toyota Corolla oil.

If you do not want to spend your money on a car service, but are ready to perform the replacement yourself, then we recommend that you read this article.

An internal combustion engine has many moving parts that require high-quality lubrication. Its role is played by motor oil. This working fluid performs the following tasks:

Cools very hot engine components, acting as a thermal conductor.
Reduces wear on moving parts.
Maintains stable engine operation at high temperatures.
Increases vehicle fuel efficiency.
Prevents the formation of soot, as well as various deposits on parts and mechanisms located in the combustion chamber.

What happens if you don't change the oil?

Over time, even the highest quality motor oil loses its properties and, accordingly, cannot effectively perform the tasks described above.

This will lead to accelerated wear of parts, increased fuel consumption, and in the worst case, cause engine failure.

The cost of engine oil compared to engine overhauls is incommensurable, so it is necessary to change the oil in your Toyota Corolla as soon as the need arises.

When to replace

This parameter is individual for each car. The first place you can find detailed information is in your vehicle's manual. However, this is a general figure and does not take into account many parameters. Some drivers recommend replacing them every 10-15 thousand kilometers. The frequency of replacement is influenced by many factors, namely:

Technical condition of the machine.
Intensity of use (daily or only on weekends).
Time spent in traffic jams.
Seasonal driving time (summer or winter);
The quality of the fuel and the oil itself.

Active vehicle use in urban environments requires frequent oil changes. There are also several visual signs that will help determine the need for replacement.

You should warm up the car to operating temperature, and then use a pipette to collect a few drops of oil. After this, drop a couple of drops onto regular or filter paper. Wait until they dry. The resulting spot will consist of an inner and outer circle.

If the mark is light in color and the contours of the outer spot are blurred, then the liquid can still serve. If the contour has clear shapes, and the color of the spot is dark, almost like carbon deposits, then an oil change in the Toyota Corolla engine is necessary.

The appearance of a leak or accelerated consumption indicates problems that are recommended to be resolved before the replacement procedure.

Which oil to choose

One of the most popular questions is what kind of oil to fill in a Toyota Corolla. The best option is to use the oil recommended by the car manufacturer.

In the technical description of the machine you can find all the necessary information. Toyota engine oil guarantees maximum service life and will effectively lubricate and cool engine parts.

The only drawback is the high price of the original products.

If you don’t want to overpay, you can take a closer look at products from brands such as Mobil, Shell, Castrol, Genuine. It is recommended to use synthetic or semi-synthetic oils. They have many advantages, in particular:

Resistant to temperature changes.
They have better fluidity at low temperatures.
They have less volatility.
Characterized by increased durability.
Retain their characteristics longer.

Mineral-based products are suitable for older vehicles up to 2000.

Changing the oil in a Toyota Corolla engine - basic steps

Every motorist can complete this task in a garage. At the same time, it is also necessary to replace the Toyota Corolla filter, so buy this part before starting.

Prepare a set of keys and a small 5-6 liter container for used oil.

It is recommended to place the car on a lift or use a pit, as the work will be performed under the bottom of the vehicle.

To change the oil in a Toyota Corolla, do everything according to the following instructions:

Run the car for a few minutes to allow the oil to become more fluid.
Take the key number 14. Unscrew the drain cap under the engine. Place the prepared container in advance. Drain the used fluid.
You can use a syringe to remove any residue from the neck. Screw the plug into place and then tighten it with a wrench.
There is a filter container next to the drain hole. Unscrew the cap with the filter. You will need a special wrench with a cup, but you can use a wrench with semicircular jaws.
Remove the structure from the socket. Remove the old filter from the cover and then install the new one. Replace the rubber gasket.
Reinstall the filter.
Fill in new engine oil in the required volume.

After this, be sure to check the oil level. The indicator should be within the MIN and MAX marks. Start the car. Make sure there are no leaks anywhere.

As you can see, the whole procedure is not very difficult. It will take you a maximum of ten minutes, but this way you will save your money. Changing it yourself has another advantage - you personally control what oil is poured into the car. Some car repair shops may fill you with low-quality products without your knowledge.

If the material was interesting or useful for you, publish it on your social network page:

Source: http://jrepair.ru/to-toyota/zamena-masla-v-dvigatele-toyota-corolla