How to choose a battery by car make

Battery house - How to choose a battery according to the make of the car?

If you prefer to buy batteries in auto stores, then you need to be guided by the following rule:

sedans and hatchbacks with an engine capacity of up to 1.6 liters have batteries with a capacity of 45-55 Ampere/hour;
station wagons with a volume of 1.3-1.9 liters - 60 Ampere/hour;
crossovers and SUVs 1.5-2.3 liters - 66 Ampere/hours;
trucks weighing up to 3.5 tons and engine capacity 1.6-3.2 liters - 77 Ampere/hour;
middle class trucks 1.9-4.5 liters - 90 Ampere/hour;
truck tractors - 2 batteries of 200 Ah.

It is clear that in each specific case you need to follow the manufacturer’s recommendations. In addition, you can easily find catalogs, including on the Internet, where you will find information on any car model.

Technical characteristics of the battery The main parameters of batteries include:

Rated voltage. Today, all passenger cars are equipped with 12-volt batteries. For trucks, special equipment, buses, and military equipment, you should buy 24-volt ones. Although 12-volt batteries may also be suitable for light trucks.

Battery capacity . This parameter is measured in Ampere-hours (Ah). This is a symbol, it means that, for example, a 60 Ah battery is capable of providing a load of 1 Ampere for 60 hours, or 4 Amperes for 15 hours. This is why batteries are discharged if you forget to turn off the radio at night or leave the headlights on.

Starting current . Starting current is the current that is supplied to the starter when the engine starts. This value is measured in Amperes. You need to very carefully select a battery with the starting current for which the starter is designed, otherwise two options are possible:

There is not enough current to turn the starter.

The starting current is not a constant value and depends on the air temperature, the area of contact with the terminals (have you noticed that over time the terminals oxidize or come off and the engine cannot be started?), battery capacity and charge level.

The starting current value is indicated on the label and corresponds to the current strength at a temperature of 18 degrees below zero. In winter, the strength of the starting current decreases and it is more difficult to start the engine, so for cold regions it is permissible to buy a battery with a reserve starting current - several tens of amperes higher.

Please also note that starting current can be measured according to different standards: EN (European), DIN (Germany) and GOST (Russia) - they are measured the same way, SAE (USA). So, for example, if you buy a “sixty” A-Mega, it will say:

starting current EN - 600 Amperes;

DIN - 365 A;

SAE - 650 A.

Polarity is the position of the positive and negative electrodes of the battery.

She may be:

straight - the positive terminal is on the left (the battery is turned towards you with the side on which the terminals are);

reverse - plus on the right.

Accordingly, you can see the battery designations: 60(0) Ah - right plus, 60(1) Ah - left plus.

If you choose a battery with the wrong polarity, there may not be enough wire to connect it to the terminal. Also look at the terminals, they can be standard thickness - European, and thin - usually for Asian batteries.

Well, pay attention that the new battery is suitable in size and mounting method

Incorrectly selected battery

If the battery is selected incorrectly - with a higher or lower battery capacity, this will be reflected primarily on the battery itself.

If the battery capacity is too large, constant undercharging will occur - the generator is not able to generate the necessary voltage to charge the battery. Over time, you will notice that the electrolyte will turn white, and it will be impossible to start the car - the battery will be constantly discharged.

If a battery with a lower capacity and starting current is selected, then, on the contrary, it will be constantly recharged. Because of this, the process of shedding the plates will begin much faster, and short circuits of the cans are possible. A clear sign of an incorrectly selected battery is brown electrolyte due to crumbling plates.

In both cases, the battery will not be subject to replacement due to a complaint.

What else should you pay attention to when purchasing?

The battery is a warranty item, so it should be checked in front of you:

measure the density and level of electrolyte;

measure the voltage - not lower than 12.5 Volts;

connect to the load plug and apply a load - the battery should hold it (the ammeter needle stays at 10.5 Volts for 5 seconds), the electrolyte does not boil and no steam is released.

Make sure to fill out the warranty card; it must have the company’s seal, the seller’s signature, and the battery serial number, which is stamped on the cover. Keep the warranty card at home so as not to lose it.

A good rechargeable battery lasts an average of 2-3 years, depending on operating conditions.

Also, a lot of fakes have appeared recently.

If the battery seems too light to you, this is an alarming sign - the manufacturer saved on lead and plates. Any store that officially sells batteries is required to present a quality certificate, and the warranty is filled out on the official letterhead of the manufacturer.

Don’t try to save money, buy a battery with the characteristics specified in the car’s instructions.

Source: http://akb55.ru/news/kak-podobrat-akkumulyator-po-marke-avtomobilya

Battery for passenger cars

The battery is an irreplaceable element of the car, without it it is impossible not only to start the car, but if the battery is unstable, the normal functioning of the electronics is impossible.

It is best to select a battery based on the car brand with the help of our highly qualified specialist who will select the most suitable battery in more detail and competently. .

This will make it possible to ensure its uninterrupted operation during installation. We have taken into account all the necessary characteristics, offering this or that battery model from such well-known companies as bosch and volt.

Search by car make

Select brand

The battery should be selected taking into account several parameters.

There are a lot of models on the market and the most important thing is that the battery capacity matches that required for your car. It is measured in ampere hours, information about which is contained not only in the accompanying documentation, but also on the device itself. You should not overpay for additional features; some of them may not be useful to you or may not be suitable at all.

The dimensions of the battery must correspond to the size of the space intended for it under the hood or in the trunk (if it is a spare battery, for example). If this is not taken into account, then it may not fit, or lead to more unpleasant consequences when the wires touch other metal parts, for example, the hood, and this will lead to a short circuit or fire.

Selecting a battery according to the make of the car is also important because it takes into account other characteristics of the device, for example, polarity. Your car may have “straight” polarity, when the “negative” terminal is on the left, or “reverse” polarity, when the “plus” is on the right. We will offer a model that matches your car.

The cost of a battery depends on the size, capacity and ability to service it. The most reliable and safest are maintenance-free batteries.

Their performance characteristics are significantly higher than those of serviced and low-maintenance models. However, their cost is slightly higher than the price of other batteries.

Cheap and high-quality batteries include Volt Classik batteries.

Car battery for passenger cars

BOSCH

VARTA

VOLT

TYUMEN

SILVER STAR

GIGAWATT

Sputnik

Contact

ATLAS

ENERGIZER

TYUMEN

Source: https://www.AKB-market.ru/dlya-legkovih-avto/

How to choose a battery by car make?

Although modern production technologies can significantly increase the life of batteries, the need to replace them still arises sooner or later.

Since the battery is one of the most important elements of a vehicle, it is desirable that its characteristics are ideally suited for a specific car model.

In some cases, the car manufacturer itself indicates the recommended brand of battery, but in the absence of such information, the owner of the “iron horse” is forced to search for a suitable battery.

Price

When buying a battery, many car enthusiasts try to save money and buy a cheaper battery.

Owners of budget segment cars do this especially often. To understand the fallacy of this approach, it is necessary to understand what the cost of a battery consists of.

Typically the price is determined by the following factors:

capacity;
dimensions;
type of battery (need for periodic maintenance);
brand.

The last point seems to be the most controversial. The production of most world-famous brands today is distributed across various countries, usually not the most technically developed.

Of course, they pay enough attention to the quality of the products of their branches, but with such a system, batteries with the same characteristics can be purchased at a more reasonable cost.

Although it cannot be denied that the brand’s reputation still serves as a certain guarantee of reliability.

Main characteristics

Capacity

In simple terms, battery capacity determines the amount of current that the battery is capable of storing.

To measure it, ampere hours (Ah) are used. As a rule, the required capacity is indicated by the car manufacturer in the documents, and information about the battery is usually printed on its case.

It is desirable that the values of these numbers be as close as possible. If the battery capacity is lower than recommended, the battery will be constantly in the process of intensive charging or discharging, which will lead to accelerated wear.

If you install a battery with too large a capacity, it will, on the contrary, constantly experience a lack of charge. As a result, excessive sulfation of the plates occurs, and the battery must be replaced. In addition, such batteries are much more expensive, and the buyer often overpays for a resource that he absolutely does not need.

Purchasing a high-capacity battery can be useful only when the car has a large number of additional electricity consumers: refrigerators, heated seats, televisions, etc.

At the same time, you should think about installing a more powerful generator. Also, information about the reserve capacity and cold start current is usually printed on the battery case.

The first indicator determines the time (calculated in minutes) during which the battery can operate in the event of a generator failure, and the second allows you to find out how easy it will be to start the engine, which is especially important in the cold season.

Dimensions

Before purchasing a new battery, you need to measure the dimensions of the old one.

Otherwise, the battery may simply not fit into its place. To install the battery they like, some car enthusiasts even go to the extent of independently changing the design of the battery platform, which significantly reduces operational safety.

It is also advisable to take into account the location of the terminals (batteries can have direct or reverse polarity), since the length of the wires may not be sufficient for a new battery. They will have to be built up, and this creates the risk of short circuits and fires.

As for the fastenings, they are usually standard. If the battery is the right size, securing it is usually easy.

Requires periodic maintenance

Based on the level of maintenance, batteries can be divided into three types:

serviced batteries. Today, this type is becoming increasingly rare and is represented mainly in the assortment of domestic manufacturers. Owners of such batteries have to constantly independently monitor electrical parameters: density, charge level, etc.;
low maintenance batteries. Due to slower evaporation of the electrolyte, the quality of such devices is slightly higher than that of the first type. However, their condition also requires periodic monitoring. They are divided into two categories: dry-charged (sold without electrolyte) and conventional (electrolyte is filled in at the factory). The first option tolerates long-term storage better, but the second is more reliable due to the fact that it undergoes initial testing by the manufacturer;
maintenance-free batteries. The most reliable and modern type. The batteries are completely sealed, which eliminates the possibility of electrolyte evaporation. However, if they fail (which is usually associated only with the expiration of their service life), their restoration is not possible. The operation of such batteries does not require any participation from the car owner.

Battery selection services

Those who have not been able to decide on the necessary battery parameters can use one of the following methods:

special tables that allow you to find out the required capacity by type and power of the motor;
online calculators on sellers’ websites;
manufacturers' catalogs.

The most objective (but also the least informative) is the first method. This is because the priority goal of dealers and manufacturers is to make a profit. Therefore, the main purpose of the information coming from them is often the sale of the most expensive product.

Examples of such online services:

It is on this principle that the results of calculations for online services and the location of offers in catalogs are often constructed.

As a result, the buyer can purchase a battery that is truly perfect for his car, but its price and quality will not be ideal.

Additional Tips

Additionally, when purchasing a battery, it is recommended to pay attention to the following parameters:

manufacturer, presence of barcode, holographic sticker;
terminal voltage;
electrolyte level (should completely hide the plates);
availability of guarantee;
hull integrity;
cost (should not be too low).

Summarizing

The comfort of car operation largely depends on the quality of the battery.
Since it is the owner who is more interested in the uninterrupted operation of his car than anyone else, it is best to choose the battery yourself (in the absence of direct instructions from the car manufacturer or the impossibility of following them).

This will allow you to be confident not only that the battery optimally meets all the features of operating conditions, but also that the price that was paid for it is fair.

We also recommend watching

Source: http://natapku.ru/sovety/podbor-akkumulatora-po-marke-avto.html

How to choose a battery by car make, instructions

When selecting a battery based on the car brand, we encountered the following problem.

For greater convenience, many online stores place special forms on their websites, thanks to which you can quickly select the right battery model for your car.

Yes, of course, by selecting a battery according to the car brand in this way, the buyer significantly saves his time.

After all, it’s enough to select the necessary data in the form offered by the store and voila, the answer is already ready. All that remains is to select the offered battery brands and pay for the order.

Agree, it’s very convenient. But does the buyer save his money at the same time? Now that's a question.

Having visited several online stores that sell batteries online, we came to the conclusion that not all sellers are honest with their customers.

By selecting a battery based on the car brand, the buyer hopes to get all possible options for battery brands that may suit his car, from cheap to expensive, from famous brands to unknown ones.

But usually, the final results offered by an online store, although correct, are far from all possible.

As a rule, the final results of data output are deliberately configured so that first the most expensive brands of batteries from famous manufacturers appear, which will certainly fit your car, and then come not expensive batteries, or there are no such batteries at all, although they, too, would most likely be of interest to the buyer.

Of course, the more expensive you buy a battery that is selected according to the make of your car, the more profitable such a purchase will be for the online store itself.

That’s why many online stores make the mistake of customizing the form for selecting a battery based on the car brand in such a way that it benefits them and not the customers.

Experienced buyers who have bought batteries this way more than once, of course, already know about this and try not to fall for such a marketing ploy.

But there are not so many such buyers, especially those who have been driving cars for a long time and are well versed in batteries, and many online stores use this moment very profitably for themselves.

But you can select a battery by car brand manually without using any forms that we usually offer on websites selling batteries.

And for this you don’t need to know higher mathematics or quantum physics, just understand a few simple points and you are guaranteed to choose for your car exactly the brand of battery that is most suitable for it.

Selecting a battery by car make, we do it ourselves

The first thing you need to understand is what the cost of batteries depends on.

As a rule, the cost of batteries is influenced by their capacity (the larger, the more expensive the battery), size (the same thing), the degree of difficulty of servicing a given brand of battery, and of course, the name of the manufacturer.

If the first, second and third points are justified, then the last point in increasing the cost of the battery is not always justified.

After all, many famous brands, for example, BOSCH, have opened factories for the production of their batteries in many countries around the world.

As a rule, these are really high-quality batteries, but you can find equally high-quality batteries for a cheaper price. After all, many buyers know that in most cases they overpay for the brand name, and not for increased quality.

The second important point is whether the batteries are serviceable or not.

When choosing a battery according to the make of your car, you must make a choice for yourself, either pay more and buy a maintenance-free battery, or pay less and buy a regular battery, which you will have to tinker with in the future.

If money allows, we recommend that you pay attention to maintenance-free brands of batteries. They are quite reliable, durable and safe.

At the same time, it is worth understanding that by paying more for such a battery model, you save on its maintenance in the future.

Many drivers use such batteries on a “set it and forget it” basis.

The third important point is the battery capacity.

The first important criterion here is the recommended battery capacity from the car manufacturer.

If you buy a battery with a smaller capacity than recommended, the battery will quickly discharge and charge quickly, there will be a constant charging and discharging cycle, and this is bad.

If you buy a battery with a larger capacity, the battery will not be fully charged, and this can lead to sulfation of the plates and rapid failure of the battery.

And yet, you will not justifiably overpay.

Increasing the battery capacity is justified when you install additional electricity consumers on the car, for example, video recorders, fog lights, on-board computers, etc.

Then the overpayment for a larger battery capacity will be justified. But in this situation, you will need to think about replacing the car’s generator with a more powerful one.

You can always see data about the battery capacity on the battery itself. It is measured in ampere hours (Ah).

The fourth, very important point is the overall dimensions of the battery and methods of mounting it.

How to select the correct battery according to the make of your car

Sooner or later, any car enthusiast is faced with the question: how to correctly select the battery according to the make of his car? The simplest answer is to look at the car's operating manual, in which the manufacturer gives appropriate recommendations.

Vehicle operating experience shows that the “native” battery installed at the factory lasts 6–8 years, no less. And, installed independently, it may not work for three or four years. Let's try to sort this issue out.

What to consider when choosing a battery

Any car enthusiast, when choosing a particular unit to replace during the repair and maintenance of his car, must side with the manufacturer. Who else, if not him, knows everything about your car.

When designing a car, all the nuances, possible and impossible situations of its operation are taken into account. Accordingly, the battery is selected in such a way that a series of cars does not have to be recalled due to problems with it.

Let's take a look, in order of importance, at what parameters should be used when selecting a battery based on the car make.

Starting current

Let's start with the fact that the starting current of batteries is regulated by several standards:

EN 60095-1 or new GOST 959-2002 - European standard;
DIN 43539 or old GOST 959-91 - German standard;
SAE is an American standard.

For example, in the DIN (German) standard, a battery with a starting current of 500 Amps when continuously discharged at a temperature with an initial current of 500 Amps will show 12.2 Volts at the very beginning, after 30 seconds - 9 Volts, after 150 seconds - 6 Volts.

The standards differ significantly. A battery marked 600 A (EN) or GOST 959-2002 will correspond to 650 A according to the SAE standard and only 385 Ampere according to the DIN standard.

Now it becomes clear why German batteries are more powerful than domestic ones, and domestic ones are much lighter than German ones with the same starting current.

What mistake do car enthusiasts usually make when changing the battery? When selecting a battery for their car, car owners are guided by the data printed on the label of their original battery, without paying attention to the standard, and buy a battery with the same starting current, but according to the Russian standard.

Video - how to choose a battery for a car:

If the battery label shows a starting current rating of 400 A (DIN), you should choose a battery with a current of at least 600 Amps in the Russian or European standard.

When determining the required starting current of the battery for a specific modification (specifically the modification, not the brand) of the vehicle, the manufacturer is guided by the following characteristics of the vehicle:

engine power;
number of cylinders;
type of engine (gasoline or diesel, the latter has more compression, therefore, more current is needed);
operating conditions (Central European, northern and extreme options);
the presence of special additional equipment;
location of the battery in the car body.

The technologically higher starting current of the battery is ensured by the thickness, area and number of plates, and the massiveness of the interbank connectors. If you install a battery with a lower starting current on a car, these elements may overheat, melt, and the battery will become unusable. In the same sense, you should be wary of “light” batteries.

Battery capacity

It is generally accepted that battery capacity and starting current are directly related. The higher the starting current, the greater the battery capacity, and vice versa. This is not entirely true. There are several ways to technologically increase the starting current. The most famous of them: increasing the number and porosity of plates, additives such as phosphoric acid.

When choosing battery capacity, it is advisable not to skimp. The larger the battery capacity, the better . The “ceiling” in the choice is determined by two sizes: overall and wallet.

The minimum battery capacity that can be installed on a car can be calculated using a simplified formula:

Battery capacity = 4 X Starting current X Start-up time (minutes)/60

The starting time in this formula is the time that you determine as the minimum for starting the car in the cold season.

Usually ten runs of 15 seconds (and no more) are enough to make sure that further efforts are useless. It's 2.5 minutes.

Thus, with a starting current of 500 Amps (DIN):

Battery capacity = 4 X 500 X 2.5 / 60 = about 80 Amp-hours

The manufacturer is guided by approximately the same considerations when determining the battery capacity.

In addition, the following are taken into account:

current consumption of vehicle systems that do not turn off after parking (radio, alarm, etc.);
natural leakage;
possible consumption of emergency parking signals.

Design

Design features taken into account when selecting batteries include:

dimensions;
polarity of the terminals relative to the front side;
terminal shape;
carrying system;
location of the gas outlet;
fasteners.

It is advisable to fulfill the overall dimensions parameter in full. Even if there is free space to install a larger capacity battery, it should be taken into account that the battery must have natural ventilation for cooling.

It is no coincidence that many manufacturers place the battery outside the engine compartment (in the cabin, or even more often in the trunk). Here you can place a more powerful battery, and it will be cooler. The battery will last longer.

In some sophisticated car models, a circuit breaking system is placed at the battery terminals in the event of an accident. They protect, of course, not the battery, but an expensive car from acid splashes in the event of a possible battery explosion. In this case, the overall dimensions and brand of the battery must be 100% observed.

Regarding the polarity of the terminals, 100% matching is also necessary, as is the shape of the terminals. Now on the market there are Asian “universal” terminals, American ones with bolts, in any case, it is better to install the battery with original terminals.

If it is possible to choose a battery carrying system from the proposed models, it is more rational to choose a system with two handles, it is more reliable.

Video - car battery sizes (DIN, JIS):

Many “original” batteries do not have a carrying system at all. This does not mean that in production they are carried with their fingers clinging to their sides; there are special devices there. Most domestic service stations, including dealerships, do not have such grips; it is safer to take a battery with handles.

Before buying a new battery, you should carefully inspect the installation location of the predecessor, especially if it is installed in the luggage compartment.

Surely there is a gas outlet there: a silicone or rubberized tube for removing vapor products and electrochemical reactions from the battery to the space outside the car. If this is not done, the interior of the car will be corroded by chemical fumes. It would be a good idea to measure the diameter of the gas outlet.

For battery mounting, the two most common options are pallet and crimp. In the first case, the battery is crimped with plates (plate) on the protrusions in the lower part of the case. Before purchasing a battery, you should check the conformity of the protrusions.

Fit dimensions are usually given on the websites of responsible sellers. The second option (crimp) is more reliable: the fastening plate is located on top. It assumes that the top area of the battery will be level.

What type of battery to choose

There are three main types of lead-acid car batteries:

serviced;
low maintenance;
unattended.

In today's market it is almost impossible to find a serviceable battery, that is, one that has full access to the insides of the battery. Most often, they are called low-maintenance batteries, that is, those with plugs to control the level and density of the electrolyte.

Video - how and which one to choose a battery for a car:

Currently, maintenance-free batteries are becoming increasingly popular. They do not have plugs or are sealed with adhesive tape; there is no need to periodically monitor the level and density of the electrolyte.

There are three main technologies.

Antimony batteries. The plates are made of lead with a small addition of antimony.

Antimony is a strong poison. This is the first drawback. Second: such batteries have increased self-discharge and charge slowly. There are also advantages: low cost and the ability to withstand strong discharge.

Calcium batteries. Pros: reduced weight and dimensions, low self-discharge. Disadvantages: high cost, reduced service life in probable cases of almost complete discharge.

Hybrid batteries. Calcium is added to the negative electrodes, and a small proportion of antimony is added to the positive electrodes. Pros: high starting current and service life, not afraid of complete discharge, large capacity. Disadvantage: the use of poisonous antimony.

Low-maintenance batteries are available in two versions: dry-charged and flooded .

It is safer to buy dry charged. A flooded battery can be stored without use for more than a year, and it should generally be purchased no later than two to three months after manufacture.

General advice when choosing a battery:

if you use your car every day, it is better to choose a calcium battery;

a hybrid battery is preferable for those who like to stay in the garage;

The most budget-friendly option that meets the needs of both categories of motorists is a low-maintenance battery.

Which brand to choose

The independent rating compiled by sellers and suppliers of car batteries accurately reflects their generalized consumer characteristics:

BOSCH batteries

Excellent value for money and quality again. And also power, durability, ease of maintenance. The secret is simple: the use of modern technologies, impeccable production. And this is not an advertising slogan, just advice.

VARTA batteries

A confident second place in sales and first in positive customer reviews. With consistently excellent quality, they have a recognizable design and a high power/size ratio.

Further listing of rating batteries will not be correct from an advertising point of view. There are excellent Korean batteries made using cutting-edge technologies, and there are also high-quality domestic ones.

The selection of a battery brand is in any case subjective, often based on the recommendations of neighbors in a garage cooperative.

Where and how to choose a battery by car brand online

There are many online services on the Internet for automated selection of batteries by car brand. This significantly reduces the time spent searching for analogues, optimizing price selection, and comparing the technical characteristics of batteries.

In this case, you should not be guided only by the data of one search service. It probably follows the commercial objectives of some seller. Here are some useful links.

Selection of BOSCH battery by car make - .

A simple service that allows you to quickly decide on the choice of BOSCH brand battery. Among the advantages are drawings of landing zones, overall dimensions, terminals, and full technical specifications.

Selection of VARTA batteries by car brand - .

A little less informative service. But it also contains advanced technical specifications.

Multi-brand service for the selection of car batteries - .

The main drawback of search services for selecting batteries by car brand is insufficient information on geometric dimensions. However, they can be easily filled by turning on the search for an already found battery. And in this case the price can be minimized.

In any case, it is useful to use an automated battery selection system based on the car brand. Not only as a guide to action, but rather in informational terms.

Adviсe

Finally, some practical advice:

Before purchasing and installing a new battery, find out the reason for the failure of the previous one. Perhaps there was a significant current leak in the car, and the battery was constantly discharged, which significantly reduced its service life.

Before installing a newly purchased battery, thoroughly clean the seat, check that there are no sharp burrs or objects that could damage it mechanically.

After installing the battery, check the leakage current in parking mode. It's better to leave this to professionals.

When purchasing a battery, provide the seller with information about your car so that he can register it in the sales document. This way you will protect yourself in case of a warranty claim. Most sellers will not support the warranty if the selected item does not match the make of the vehicle.

During operation, monitor the electrolyte level in low-maintenance batteries. Inspect the area near the battery for foreign deposits.

In hot weather, check the temperature of the battery, at least as an estimate.

Video - choosing a battery for a car:

May be of interest:

Source: http://voditeliauto.ru/poleznaya-informaciya/avtoustrojstva/akb/podbor-po-marke-avtomobilya-2.html

Selection of battery by car make - optimal batteries for your car in the 1AK-M store

Trade in your old battery and get a discount from 300 to 2200 rubles

If you need a new battery for your car, it is convenient to make a selection on this page:

– select the car brand

– choose a model

– select the modification and click “Select battery”.

In case of any difficulties, call our managers, they will help you make the best choice.

You can also enter the parameters of the required battery yourself: Selection of batteries by parameters

Or you can find the battery you need by looking at the Full list of products and prices

To select a battery according to the make of the car, you need to take into account all the necessary characteristics that distinguish the desired model. That is, the battery must match the car brand 100%.

Battery capacity

It is necessary to know the electrical capacity of the required battery. Capacity is measured in ampere hours. Information about the exact parameters is contained in the accompanying booklet and is present on the battery itself.

Car enthusiasts need to take into account: you shouldn’t overpay for additional features, especially since they may not be useful, or even not suitable at all.

At the same time, a battery with insufficient capacity will not be able to provide the car with the required level, which will lead to problems during its operation.

Selecting a battery for a car involves taking into account “Reserve Capacity” - an indicator of the time during which the car can operate with a faulty generator. For example, for a battery with a capacity of 55 Ah, the figure is about 1.5 hours (if fully charged). During this time, you can take the necessary actions.

Selection of dimensions

Correct selection of batteries according to the make of the car requires precise adherence to the dimensions. The fact is that even a deviation of 2-3 cm from the required dimensions can cause many problems. The dimensions of the battery must be suitable for the space intended to be placed under the hood or in the trunk (in the case of a spare battery).

If the dimensions do not match, the battery may simply not fit. Or even the battery terminals will touch the body or other parts of the car, which, of course, is unacceptable. It should be said that it is best to avoid the advice of experienced motorists regarding the possibility of “adjusting” the battery to the car.

This will not lead to anything good.

Cold start current (starting current)

When selecting batteries for a car, you must not forget about such an indicator as “Cold Cranking Amperes”. This is the maximum possible current that the battery can withstand in a short period of time (30 seconds) when the engine starts in the cold season. This indicator in Russia is regulated by GOST, in other countries - by relevant requirements.

Polarity selection

Polarity can be “straight” when the “negative” current lead (terminal) is on the right, or “reverse” when the “positive” one is on the right. When determining the polarity, the battery must be turned with the terminals towards you.

Polarity must match factory specifications. In some cases, motorists install a battery of a different polarity. But for this you need to redo the wires and increase their length.

And this requires certain skills: you need to select wires that meet all the requirements and make the correct fasteners.