How to replace a low beam light bulb

How to replace a low beam light bulb yourself?

Having a vehicle obliges the owner to learn new skills and systematically carry out cosmetic repairs to the car or improve the functioning of systems and parts.

Therefore, every driver sooner or later has the question of how to replace the low beam light bulb. Of course, you can always go to a car repair shop, but it’s much easier and faster, and most importantly, more economical, to do everything yourself.

The proper functioning of the headlights will ensure safe movement for the driver, so this problem should not be neglected.

Step-by-step lamp replacement

When the light goes out in one of the headlights, the driver first tries to find out the cause of the problem. If it is associated with a failed lamp, then you should replace the device with a new one. If this problem occurs and if the driver is not aware of how to change the low beam lamp on a viburnum, we suggest using the following instructions:

You need to start working by opening the hood and turning off the power. To do this, you need to remove the negative terminal from the battery.
Having moved the washer reservoir, the driver must remove the cover-cover and remove the burnt-out device.

Replacing a low beam light bulb on a car

The lamp is removed by squeezing the latch.
At the next stage, the terminals from the lighting device are disconnected, and a new low beam lamp is installed on the Kalina car.

To correctly place the lamp in the right place, it is recommended to remember how it was originally connected and where the wires were located. Do not touch the glass of the lamp with your fingers, as this may damage the device.

Replacing low beam lamps

When changing the lamp, it is recommended to follow these rules:

When checking electrical equipment, you cannot check the serviceability of the circuits.
It is not advisable to use fuses that are not provided for this car model or use wire instead.
When changing fuses, do not use screwdrivers, otherwise a short circuit may occur.
The battery must not be disconnected while the engine is running.
Working with LED lamps must be done with gloves.
Due to the decrease in luminous flux power, lamps should be changed regularly.

The driver must remember that after it gets dark, it is forbidden to drive with faulty headlights.

Replacement of low beam lamps is carried out after disconnecting the battery terminal

Why might the low beams not turn on?

In addition to burnout, the lighting device may not turn on for a number of reasons:

Relay contacts have oxidized. To understand that this particular reason caused the lamp to turn off, you need to listen to how the relay works. If the contacts are oxidized, the relay will constantly click. To eliminate the breakdown, you need to clean the power terminals.
The fuse has blown. This equipment cannot simply break; perhaps liquid got on the lamp base, resulting in a breakdown. The fuse should be changed and the cause of the problem should be identified.
If there is zero voltage at the connector contacts, then it is better to immediately contact a technician; you will not be able to solve the problem yourself.

In the absence of all of the above reasons, the probability of the lamp burning out is 99%.

Step-by-step instruction

All H7 type lamps are connected in the same way. They are equipped with a metal base, which is pressed against the headlight by a wire bracket.

What's better to buy?

There is a wide range of automotive products on the market. Many models differ in cost due to the power of the product, manufacturer, appearance and other characteristics.

Low beam lamp PHILIPS X-treme Vision +100%

Philips, OSRAM and BOSCH companies offer reliable, high-quality, durable products at an affordable price. Drivers who prefer yellowish light will like BOSCH brand lamps. For those looking for devices that last a long time, look no further than Philips. OSRAM offers products with high color temperatures.

How to make a replacement?

Before changing the low beam bulb on Kalina, it is advisable to familiarize yourself with the replacement principle.

Replacing a light bulb on a car's running lights always starts with disconnecting the battery. Only when the network is de-energized can you get to work.

The first step is to disconnect the terminal block, which is located under the cover plate. The block with terminals is pulled back without the use of tools (screwdrivers or pliers).

To get to the lamp base, you need to use pressure to disengage the wire bracket and boldly pull out the lamp. You need to install a new lamp by performing the same steps in reverse order.

To tighten the bracket while securing the base, use a flat-head screwdriver.

You need to check whether the lamp works only after assembling the headlight and connecting it to the battery. It is recommended to change lamps in pairs, left and right at once. It would be a good idea to adjust the lighting after finishing the work.

Replacing the low beam lamp on Kalina

Why do lamps burn out too often?

For proper operation of the lamps, it is necessary to maintain the voltage that is included in the lighting system by the manufacturers. As a rule, the voltage supplied to the device contacts should be 13.5 W. Very often, when charging a battery, the voltage is brought to 14.2 W, which automatically reduces the service life of the lamps.

You can use a multimeter to measure the battery voltage. The procedure requires that the motor be turned on.

When the lampshade is constantly exposed to external factors, for example, the headlight is not sealed and moisture gets inside, the bulb becomes dirty, which is why the lamp can quickly stop working.

note

Replacing lamps on Kalina requires concentration and accuracy in the work. During the process, you should pay attention to the installation of lighting and the method of connecting the wires. This is important, because after removing the lamp, the new one will need to be installed exactly in this position, connecting the contacts correctly.

It is recommended to wear gloves to avoid accidentally touching the glass of the device. If the driver does leave fingerprints on the glass of the light bulb, the surface must be treated with alcohol.

Recommendations

When faced with the question of what running lights are on a car and how to service them, the driver of the vehicle begins to study the nuances and details of this process. The serviceability of lighting devices is mandatory for the safety of passengers and the car owner. Therefore, it is necessary to change and adjust the lighting on time and with a certain frequency.

LED low beam lamps

It is recommended to install LED low beam lamps. The advantages of the devices are their efficiency, affordable cost, and long service life.

Along with other types of lamps, LEDs occupy a leading position. For drivers who are often on the road at night, it is recommended to install hella fog lights.

They significantly improve visibility of the road surface and do not dazzle other road users.

It is impossible not to note the importance of the serviceability of the rear lights of the car. They must be powerful, have a durable body and excellent color temperature. The rear lights on the VAZ brightly illuminate the road in any weather and at night. A wide range of products allows you to choose modified spare parts with all kinds of additions and improvements. Thanks to this, the appearance of the car will become expressive and original.

Today, low beam h7 is considered the most popular and in demand. Installation is carried out on almost all cars in the same way, and the process is simple and quick.

If the driver does not understand how to replace the low beam light bulb on Kalina, we recommend that you read the instructions above. It is important to follow the rules and take into account all recommendations, then the work will be done efficiently.

This procedure will save money for the car owner.

Source: https://mensdrive.ru/osveshhenie/zamena-lampochki-blizhnego-sveta

How to replace the low beam bulb on a Renault Duster video

On all modern cars, low beam lamps are consumables.

This is directly related to the fact that, according to Russian legislation, low beams must be turned on at all times, regardless of weather conditions, visibility and time of day.

To avoid unnecessary expenses, you can change the low beam bulb on a Renault Duster yourself. Read on to learn how this is done and which manufacturer to choose.

What to choose?

In order for the light bulb on a Renault Duster to last a really long time after replacing and not have to be replaced soon, it is necessary to choose exactly the model of the light bulb that is made of the highest quality and is based on only high-quality materials.

First of all, owners pay attention to original consumables for Renault Duster, believing that using the original is the most reasonable and rational solution to the problem.

However, there are many other popular manufacturers on the market who are ready to offer low beam lamps that have greater durability and light beam power. At the same time, the price of such a product will be much lower, and the quality guarantee from the manufacturer will allow for a free replacement if the element fails ahead of time.

The specification for replacing the low beam lamp on a Renault Duster is type H7 and power 55 watts. This means that any consumable that meets these parameters will fit the Renault Duster and will not cause any complaints.

Among the most popular among Renault Duster owners are low beam bulbs from the Osram and Philips brands, however, there are many more manufacturers that also meet fairly high quality requirements.

The main criterion when choosing is appearance. When purchasing, you should pay attention to soldering, the presence of mechanical damage and cracks on the glass.

Another reason to refuse the purchase will be a violation of the integrity of the conductive thread under the glass, uneven joints and play in the base.

If there are no similar external defects on the low beam lamp, you can safely proceed with its installation and check the further performance and evenness of the light.

Owner's instructions

So, a new low beam lamp for Renault Duster has already been purchased, and the car is ready for work. Now you can start replacing.

Since the work will be carried out with an electrician, for safety reasons, it is strongly recommended that you first disconnect the battery before replacing.

This can be done using a 10-mm open-end wrench; in this case, it will be enough to “throw off” only the terminal with the “plus” sign.

If the work is to be done from the side where the battery is installed on the Renault Duster, it is best to remove it completely: use a 13mm open-end wrench to unscrew the battery mount, then it is freely removed and put away to the side.

Once access to the headlight housing is gained, it is necessary to remove the protective cover. This does not require a special tool; dismantling is done using your hands. The main thing is to make movements as carefully as possible so as not to damage the already fragile parts of the headlight.

Next, the old light bulb is removed from its regular place, to which the supply wire is connected using a terminal.

Next, you should carefully disconnect the terminal, being careful not to damage the glass or break it.

In this case, you should carefully inspect the terminal for melting and traces of mechanical damage; in this case, you will have to contact the service center to correct all existing deficiencies.

If there are no visible faults, you can connect the purchased consumable to the terminal and reassemble in the reverse order.

If for some reason the beam begins to flicker and shine unstably, this is a reason to recognize the part as faulty and contact the store to request its replacement. If the headlight does not light up at all, the fuse may have blown, it is also worth checking.

Even a beginner can replace the low beam lamp on a Renault Duster. The main thing is to strictly follow these instructions and choose a manufacturer that can provide a high-quality and durable product. In this case, replacement will not be required soon, but even and bright light will allow you to easily move in conditions of poor visibility and in the dark.

Watch an interesting video on this topic

Source: https://eurasia-avto.ru/kak-zamenit-lampochku-blizhnego-sveta-na-reno.html

Problems with low and high beam lamps: causes and solutions

Home page » Electronics » Light and sound devices » Problems with low and high beam lamps: causes and their elimination

Incorrect operation of automotive optics

For what reasons do low beam lamps burn out? What to do if your car's low beams don't work?

There may be several reasons:

If the low beam does not turn on or light up, this may be due to a failure of the light bulb itself. Depending on the design of the optics, the low beam may not work, while the high beam may function quite normally. If you use halogen lamps equipped with two filaments, then the reason may lie in the rupture of one of these filaments. As a rule, if one low beam headlight does not light, this is due precisely to the inoperability of the lamp.
The next reason why a driver may think that a low beam lamp needs to be replaced is a fuse failure. The optics may well not turn on due to the fact that the fuse may have burned out. To identify this, you need to open the fuse box and find the burnt out element. By removing the device and replacing it with a new one, you can get rid of the problem. If fuses constantly and often blow out, this may indicate a possible breakdown in the car's electrical circuit. In this case, most likely, you will need to seek help from an electrician, but you can also check the wiring yourself.
It should be noted that wiring problems can be found in different places. Therefore, the car owner needs to diagnose all the pads that are connected to the safety unit.

For example, the block may be poorly fixed; sometimes the reason why current does not pass through may be oxidation of the contacts. If the problem is in the fastening, then the nuts just need to be tightened, if in the contacts, then they need to be cleaned.

Sometimes this happens: the light bulb does not work due to oxidation of the wire on the switch itself. This is especially true for domestically produced vehicles.
In some cases, the reasons why the low beam headlights cannot light up are related to the engineering solutions of the designers. It happens that one headlight may not function due to the fact that the operation of the purifiers is disrupted. For example, this is true for Niv. In this case, the operation of the low beam is ensured by the electric motor, since the entire system is tied to it. So if the motor fails, the optics may well not work. In any case, if you encounter unusual reasons, it would be better to seek help from a professional electrician.
It happens that the mass on the headlight disappears and then there is no light.

Tester designed for continuity testing of electrical circuits

Which bulbs are best for low beam headlights?

If you think that once you install a high-quality low beam lamp, you can forget about the need for replacement, then you are mistaken. From time to time you will have to change the optical elements anyway. But in order to remove and change the lamp as rarely as possible, you should choose the right element.

Today there are several types of light bulbs:

Incandescent - the simplest type, is a filament enclosed in a bulb. When the element operates, this filament is heated. With regular use, the thread will become thinner and eventually burn out.
Halogen - in this case, the filament is surrounded by a special halogen gas, due to which the temperature rises, which leads to improved lighting. The service life of halogen lamps is much longer than that of the bulbs described above, it reaches about 1000 hours.
Gas discharge - in this case, lighting is created as a result of heating gas under high voltage. Such devices usually use xenon, which is characterized by high luminous efficiency. To provide power and enable xenon, additional devices are needed, but in general such a system significantly increases the cost of optics. The service life in this case can reach 2 thousand hours.
LED light bulbs have recently become increasingly popular among domestic buyers. They can last up to 3 thousand hours or more depending on the manufacturer and usually have a white lighting color. It should be noted that LED elements provide better road illumination while consuming an order of magnitude less energy.

Five varieties of Osram light bulbs

Why don't the high beams work?

If the low and high beams or only the high beams do not light up, the reasons are as follows:

Replacing the high beam lamp may be due to the burnout of the element itself, as in the case described above when replacing the low beam lamp is necessary.
Fuse or relay failure. You need to find the relay block and check the functionality of the element.
The problem is in the operation of the steering column light switch.
If we are talking about an old car, it may be necessary to diagnose the mass. The resistance to ground should be no more than 5 ohms.
As in the case of low beam lighting, the cause of the malfunction may lie in oxidation or broken contacts. If we are talking about a break, then checking the electrical circuit will allow you to identify it (the author of the video is the channel I adore the Internet).

Replacement instructions

If the headlights do not light up when the optics are turned on, and the problem is related specifically to the light bulbs, then you will need to replace the low or high beam lamp.

If you do not know how to remove and how to replace low beam or high beam lamps, below are instructions that will help you understand this issue:

Before changing the low beam bulb, you should completely turn off the voltage in the electrical circuit of the car, this will avoid possible short circuits. To do this, open the engine compartment and disconnect the terminals from the battery.
Then go to the headlight itself and remove the protection that covers the optical elements. Depending on the design of the vehicle, protection may vary. It can be fixed with bolts, and the light bulbs can also be protected by a plastic cover that just needs to be unscrewed. In general, to dismantle the protective element, you need to be guided by the situation. If you have any questions, try to find answers to them in the service book.
After removing the protection, disconnect the power supply and unscrew the socket that secures the lamp itself. Carefully remove it and replace it with a new one. Before installation, it is advisable to treat the flask itself with medical alcohol, otherwise it may burn out immediately. When installing the bulb itself, you should not handle it with your hands, as fingerprints will worsen the illumination. If you need to handle the flask specifically, use a dry cloth. Further assembly of the structure is carried out in reverse order.

Sorry, there are no surveys available at this time.

Video “How to properly change light bulbs on a car”

A detailed step-by-step procedure for replacing optical elements using the example of a Renault Logan car is shown in the video below (the author of the video is YoungGodOfSpring).

Do you have any questions? Specialists and readers of the LABAVTO website will help you ask a question

Source: https://labavto.com/elektronika/svet/zamena-lampy-blizhnego-sveta/

How to replace a low beam lamp

Home » Repair and service » How to replace a low beam lamp

The headlight of a modern car is a complex electronic device containing many different elements. The main elements are lamps, that is, light sources. Of all the lamps installed in the headlight module, those that provide low beam burn out most often.

For halogen lighting devices, the MTBF is 500–750 hours. Halogen lamps are used as low beam lamps.

Let's look at how to replace halogen lamps equipped with an H7 base: for low beam sources this size is the main one.

Let's look at the reasons why the low beam may not be on. The current in the lamp power circuit is switched by a relay. There is also a fuse in this circuit. Be aware that most cars use separate fuses for the right and left headlights. To find out the details, don't look for a wiring diagram. You only need a diagram of the mounting block located near the dashboard.

A block containing all the relays and almost all the fuses (VAZ-1118)

You need to clearly understand where the fuse is located that closes the power circuit for a non-working lamp. You also need to find the relay responsible for the operation of the headlights. You will need this information to find out why the lamp stopped turning on:

The relay contacts may have oxidized. When you try to turn it on, the relay will click properly, but sometimes this is not enough. Only the power terminals that need to be cleaned can oxidize;
If the fuse installed in the power circuit has blown, try replacing it. However, fuses do not simply blow, and you need to look for the reason. Perhaps it was caused by liquid getting on the lamp base;
Having removed the fuse, you need to measure the voltage at each of the connector contacts. If it is 0 Volts, and the low beam was turned on, changing the lamp will be useless. It is better to immediately contact an auto electrician;
Let's say the relay contacts are cleaned, and there is 12 volts in the connector at the moment of switching on and the fuse is good. Then the reason why the light does not turn on will be the lamp burnout. This is true 99% of the time.

The headlight design in a modern car is often unique. However, lamps equipped with an h7 base are always connected in the same way. A bracket made of wire presses the metal base to the plane of the headlight.

All elements, such as the bracket and the socket connector, differ little from car to car. So you can follow the instructions with confidence that you will not make mistakes typical of novice car owners.

What is better to buy

Let's say you need to choose something reliable and not too expensive. Then products from European brands are suitable: OSRAM, Philips, BOSCH.

Philips lamps have high durability, although they shine less brightly than OSRAM halogens. The products of BOSCH and OSRAM differ little, but BOSCH does not produce sources with a high color temperature.

Some people like the light to be a little yellowish, and then BOSCH lamps will be the best choice.

Domestic brands have one advantage - low price. Lamps from the Mayak and Dialuch companies are produced in a wide range, but they do not have outstanding characteristics.

Set of low beam lamps from Mayak

There are also premium brands. They belong to companies from Japan, which have maintained leadership for many years. The prices for such products are the highest. We will leave the choice to the owner.

The low beam lamps are supplied with the same voltage as all others (12 Volts). And their power is usually 55 Watts. On the packaging you can see the following designation: “12V/55W”. The manufacturer installs exactly 55-watt lamps, but many car owners carry out “tuning”, increasing the power. This is not recommended.

Always disconnect the battery before replacing lamps. It is enough to remove the negative terminal, but even for such a simple action sometimes you need a spanner. If the network is de-energized, dismantling can begin. The lamp base will be covered with a cover, and to remove it, no special tools are needed.

Each lamp is usually protected by a cover plate

There is always a plinth under the cover. First of all, disconnect the terminal block attached to the lamp contacts. The block with terminals is simply pulled back. No pliers or screwdriver are used in this step.

The block can be removed by hand

The lamp base will be pressed against the headlight with a wire clamp. You need to press on the bracket and then disengage it.

The wire bracket is bent and disengaged

At the last step, the lamp is not held in place by anything. You can pull it out and then install a new one in its place.

The old lamp was completely dismantled

When carrying out installation, all steps are performed in reverse order. The glass needs to be cleaned, for which the “Second” product is suitable. You should not touch a clean flask with your hands, so wear gloves.

To tighten the bracket, securing the base, you usually use a flat-head screwdriver.

Having installed the protective pad in place, check the work done. After connecting the battery, turn on the headlights. Let's say the lamp does not turn on, and the fuse, which was working, has burned out. Then you need to look for where exactly the short circuit appeared. Most likely, the positive wire was connected to the body.

It is better to change lamps in pairs, left and right at once. Even after replacement, it is recommended to carry out adjustments.

Adjust the direction of the light beam

Having driven the car away from the vertical plane by 5 meters, turn on the low beam. The top edge of the beam should be 75 mm lower than the center of the headlight. The boundary of the spot has the shape of a broken straight line, and the break point in the diagram is indicated by the letter “E”. Point "E" should not be moved to the left or right.

The car instructions indicate where the headlight adjustment screws are located. One of them adjusts the vertical tilt, and with the help of the second one changes the direction of the beam “right-left”. Something else hasn't been invented yet.

Why do lamps burn out too often?

The voltage supplied to the contacts of the halogen lamp should be 13.5 Volts. But in reality everything looks more complicated. When the battery is charged, the voltage in the network is specially brought to 14.2 Volts. This reduces the service life of the lamps.

Voltage, V	Relative brightness, %	Relative service life, %
11,48	53	1000
12,15	67	440
13,5	100	100
14,18	120	50
14,85	145	28

Take voltage measurements of the on-board network. Let's say that at high speeds the value exceeds 14.4 Volts. This means that the generator urgently needs to be repaired. Most of the time when the engine is running, the generator produces exactly 13.5 Volts. Therefore, there is no need to lower the voltage by including a choke or resistor in series with the lamp. This will result in a decrease in brightness.

To measure voltage, a multimeter is connected to the battery terminals.

Need access to both terminals of the standard battery

During the experiment, the engine will need to be started.

The reason why lamps fail may also be insufficient tightness of the headlights. If the lampshade constantly fogs up, then it is clear that the bulb will not remain perfectly clean. In general, frequent lamp burnouts are a reason to contact a car dealer (here we are talking about cars that are not out of warranty).

Someone in their reviews reports that they change lamps with an H7 base every two months. There are other reviews that say that one set of lamps lasts for a year. In fact, the service life is always indicated on the packaging, and it is 500 or 750 hours.

In a good way, these numbers can be multiplied by 2, and if the lamp burns out earlier, we need to look for the reason. There may be a fault in the on-board network. Few people have heard of counterfeit lamps, unlike spark plugs. Products manufactured using simplified technology are another matter.

Our advice here is this: carefully study the packaging.

autozam.ru

How to change a low beam light bulb?

Good light at night can be compared to good vision during the day.

It is light that plays a key role in the motorist’s awareness when driving at night; if the headlights shine dimly or do not shine at all due to a burnt-out light bulb, you have every chance of getting into a big accident, the consequences of which can only be guessed at... Non-working headlights need to be repaired , and we will tell you how to do this in this article. You will learn how to replace the low beam light bulb on your car with your own hands.

When do you need to replace a low beam bulb?

According to traffic rules, operating a car with faulty lighting equipment, especially at night, is prohibited. This establishes a “List of faults and conditions under which the operation of vehicles is prohibited.”

If your SUV's headlights do not work properly or are dirty to the point where the light from the headlights cannot pass through the lens, you are not allowed to drive.

In addition, any vehicle poses a potential danger to all road users, especially if it is not visible due to bad weather or insufficient lighting.

Therefore, if the headlights do not provide sufficient illumination, their lamps must be replaced. As a rule, one lamp burns out, not two at once. For owners of some car brands (and this is far from a secret), low beam lamps are often a real headache.

Messages on car forums like “I changed the lamp two months ago, but it burned out again” come in dozens and hundreds. In addition, the very intensity of the low beam does not suit all car enthusiasts.

The “Japanese” and, of course, cars from the domestic automobile industry are especially guilty of this.

Some tips or things to remember?

1. Any repairs to car headlights or those that concern the electrical equipment of the car should be carried out only after you have disconnected the battery. It can only be connected when the ignition is turned off.

2. Do not check the serviceability of the circuits for a spark when checking electrical equipment, otherwise the electrical components of the car may fail.

3. Do not use fuses that are not designed for use in the car or are designed for too high a current. Also, wire cannot be used instead of fuses.

4. When replacing fuses, it is strictly forbidden to use screwdrivers, since a short circuit may occur in the electrical circuits.

5. When the engine is running, it is strongly recommended not to disconnect the battery to prevent the voltage regulator from being damaged and to prevent damage to electronic equipment.

6. Low and high beam lamps in cars may be halogen, so you should not touch them, since grease stains cause a certain degree of darkening of the windows.

7. It is better to replace LED low beam lamps while wearing clean gloves. Wipe the surface of the lamp with a clean cloth treated with alcohol if you accidentally touch it.

8. Over time, the lamp may darken, therefore, the light output will decrease. This is why the low beam lamp must be replaced regularly. Don't wait until it burns out.

How to replace a low beam bulb?

When you first encounter the problem of replacing a fuse, you first intuitively have to look for the fuse block. It is often located in the engine compartment next to the battery. We press back the latches of the cover under which the fuses are hidden, remove it and look inside. There we see, as usual, fuses of different power and size.

If a large fuse, although difficult, can be removed simply by hand, then a small one cannot. You'll have to look for small pliers or tweezers.

In addition, many automakers leave a diagram on the inside of the fuse box cover that allows you to determine which electrical circuit each fuse is responsible for.

Sometimes such a diagram may not be on the cover; it must be found in the operating instructions.

If everything is in order with the fuses, and the light bulb in the headlight does not shine, then the next step is to check and replace the lamp. Getting to the headlight bulbs is easy. You just need to remove the rubber plug from the back of the headlight from the engine compartment. This opens a hole for access to the lamps. The size of the hole, at first glance, is normal; the hand fits through it freely.

It should be easiest to remove the turn signal lamp. It is quite easily removed from its mount in the headlight unit. Difficulties will be caused by dismantling the low beam lamp.

Sometimes you may not be able to disconnect the lamp mounts by touch by touch, and it may not be possible to look inside without removing the entire headlight. In this case, you can use the services of an online consultant from one of the brand’s salons.

Remove the lamp carefully, as you may receive minor injuries in the form of scratches on the skin on the sharp plastic edges of the hole in the headlight unit.

Please note that the lamp sits quite tightly in its socket, and it is safe to pull it with force. But doing this is inconvenient. However, this task is quite doable. Thus, replacing the lamp and fuse is possible, but quite troublesome.

If you do not have your own tool, and you do not consider it useful to know the design of the headlights and the fuse diagram, then it is better to have specialists change the lamps and fuses in your car.

But if the car service is far away or it’s too expensive for you to go there, a “handy” colleague will help you do it in half an hour.

If after replacement the lamps burn out too quickly, this could happen for the following reasons:

1. The voltage regulator in the generator is faulty, the voltage is jumping, the brushes may have “flyed”.

2. The quality of the lamps themselves can be poor, as they are often counterfeited.

3. Too much current in the lighting circuit.

4. When installing the lamp, you touched it with your hands

5. The problem is in the fuse box.

A faulty light in a car can cause an accident in which people may be injured. As a rule, in the event of a traffic accident, the driver whose lighting devices do not work or do not meet the required parameters is often found guilty. Therefore, responsibility for the condition of the lighting devices lies entirely with the car owner.

Source: http://autofluids.ru/remont-i-servis/kak-zamenit-lampu-blizhnego-sveta.html

Replacing the low beam lamp on a Nissan Beetle

Replacing low/high beam headlight bulbs on a Nissan Juke cannot be called difficult, but changing a headlight bulb is even easier. Therefore, if you need to change a burnt-out light bulb on a Beetle, you can do it with your own hands in literally no time. The main thing is to know what kind of light bulbs you need and buy them in a store or order them online.

Nissan Beetle lamp replacement price

By the way, sellers probably set the price depending on the price of the car, because despite the fact that H4 bulbs are the same for all cars, if you are looking specifically for a Nissan Beetle, they will be a little more expensive.

For example, a regular Osram lamp will cost about 150 rubles. , and COOL BLUE INTENSE H4 is not less than 400 rub .

And if you change light bulbs at a service center, you will have to pay another 300 rubles for the work .

Replacing the H4 light bulb Nissan Juke

The procedure for replacing lamps in the low and high beam headlights of a Beetle does not require absolutely no tools , we do everything with our fingers, although there is not enough space to get to the light bulb, one headlight will take no more than a couple of minutes. In the photo you can clearly see the process of replacing a low beam lamp + how to change a Nissan Juke headlight bulb.

Before you start replacing headlight bulbs, be sure to remove the terminal from the battery.

It won’t be very convenient to get to the low/high beam bulb of the Nissan Zhuk (there is not enough space), but it’s quite possible to do it with two fingers. Once you open the hood, you will need to find a large rubber circle with a connector in the middle.

Immediately carefully remove the connector.

Then, with the same dexterity, a rubber protective boot.

The light bulb in the headlight is held in place by a bracket, and to remove it you need to squeeze the antennae and move them back so that they come out of the clamps, and then lower them down.

Now all that remains is to take out the light bulb and replace it with a new one.

Now let's install everything back. By the way, it is worth paying attention to the fact that the lamp is inserted in only one position.

Finding and changing the headlight bulb will be even easier than the low beam one. We look behind the top headlight, turn the rear part of the lamp holder counterclockwise a third of a turn and pull out the side light bulb along with the socket. Then we simply take it out and replace it with another one.

By the way, these are the ratings of the light bulbs used on the Zhuk. The low/high beam bulb H4 alone is responsible for this and that light. The dimensions include W5W, which are often replaced with LED ones to make them shine brighter. And if you suddenly have to change the PTF lamp H8, then you can install H11, which will also work if you remove the jumper in the connector.

Source: https://rocketmotors.ru/remont/12/20/zamena-lampy-blizhnego-sveta-na-nissan-zhuk

How to replace a low beam light bulb on a Mercedes

Replacing low beam bulbs. Posted by hunter, March 23 After 5 years, it’s time to make a photo report on replacing low beam bulbs (xenon).

Mercedes -Benz E-class E200 CGI, black obsidian › Logbook › Replacing low beam lamps. CVT was 2 hours ago. A week ago my right low beam bulb died.

To replace the lamps in the front headlight of a Mercedes-Benz C-Class, do the following: Open the headlight housing cover counterclockwise (the low beam lamp is located on the edge, and the high beam lamp is closer to the center of the car.

Replacement of low beam bulbs! And on what cars - on serial Mercedes Read more. Send a private message to SHEFF. Attempts to remove the leash using improvised means were unsuccessful.

Replacing the low beam lamp of Mercedes dimensions

The lamp burned out, I decided to change it, but I couldn’t figure out how. In short, it feels like she just died there. I pulled so hard that I tore off the base; the input from the light bulb itself does not come out of the connector. And in general, maybe I’m doing something wrong, some kind of nonsense, I didn’t think that changing a light bulb is such a hemorrhoid in a Mercedes.

The light bulb on the fog lamps is understandable, it’s as simple as changing, but here it’s kind of a bummer. The headlight itself is Bosch if it matters, simple halogens.

Has anyone encountered the problem? Did you remove the socket where the light bulb is attached? I've never had any problems with removal. It is a little difficult to install at night in the dark, since you have to click it by touch..

So, did your electrical connector melt or stick to the light bulb?

This happens, you can buy regular electrical connectors instead. It’s just not clear that you have BOSCH headlights. This kind of crap is common with Depot and the like.

This happens because the light bulb begins to shine brighter before it burns out and, accordingly, heats up more. This happens because the coil breaks, but due to the inductance, a spark is formed that welds it again, as a result it turns out that the coil current becomes shorter More flows through it, and so on, until it breaks completely.

Slowly, on two headlights. Everything is simple and clear. I barely got through to the dimensions, I almost left my hand there.. It took about an hour to replace the neighbor and the dimensions.

The Japs are somehow not designed to replace light bulbs. I changed the front dimensions on the Lancer, so it’s better to say: I changed the rear ones - I had to remove the lights! Recently I changed this. The guys were really having fun. I was with a friend, drinking beer, crying and changing, crying again, changing again. It was tough, I'm not kidding.

Please login or register. Did not receive your activation email? I can't change the low beam bulb. Topic: Can't change low beam light bulb. Tell me how you get them out of the connector??????

FACT! Apple founder Steve Jobs drove exclusively Mercedes cars. At the same time, without numbers. This was Jobs' calling card. According to California law, you can drive without license plates for the first 6 months after purchase. Thus, every six months Steve changed his car, returned the “old” Mercedes to the dealership and bought a new one.

Did you unfasten the spring, I’m embarrassed to ask? My connector just melted, I’ll look for the same one, or mess up something……. The Japs are somehow not designed to replace light bulbs. I changed the front dimensions on a Lancer, so it’s better to say: Quote.