Starting the car from the pushrod

How to jump start a car?

Of the various reasons for a car engine’s failure to start (spark plugs, starter, poor fuel, depressurization of the intake tract, fuel pump malfunction), the first place to be put is insufficient battery charging and battery wear. In Russia, these reasons are often aggravated by frosty weather.

How to start such a car from a pushrod?

Pushing launch

The meaning of all mechanical starting methods (pushing the car by assistants, starting from a tow, when going down a hill) is the same.

By applying mechanical force to set the car in motion, you transmit the torque of the wheels to the engine (through the transmission).

Moving engine components do not require significant effort from the starter or increased energy from the battery, so simple engines start quite easily.

Starting the car “from a pusher” works normally for older domestic models with carburetor engines. Some experienced owners of worn-out domestic cars specifically choose downhill parking spots, using them for regular starts that “save” the battery.

Ways to start a car “from a pusher”

For cars with a carburetor engine, you need to pump up the fuel before starting. Two or three presses of the accelerator pedal (to the floor) is enough for this. In older models, you can pump up the fuel with a manual fuel pump.

With injection engines such manipulations are not necessary. In cold weather, you need to check the condition of the exhaust pipe. It may be clogged with snow and ice. If there are signs of frozen condensation, starting with a pusher is unlikely to help.

When classically pushing a car, assistants (three or four people) are needed, then the driver can remain behind the wheel. With a small, weak composition, the driver has to get involved in the process (from the driver’s door).

Video: How to start a car from a pushrod

Before this, you need to insert and turn the ignition key, set the gear to neutral.

Having gained sufficient speed, the driver needs to have time to jump into the car, squeeze the clutch, engage the gear, and smoothly release the clutch.

There are differing opinions about which gear you should try to start from. The recommended start from third gear leads to a strong jerk of the belt and timing chain, which can break.

For carburetor engines, you can assist starting with the gas pedal. Injection engines in this mode include purging of the combustion chambers (without fuel supply), so it is better not to touch the accelerator.

The hill start technique is no different. Having squeezed the clutch, you release the handbrake and select the desired gear. When the clutch is engaged smoothly, the engine should start. With the engine running, you need to stop, put the gear in neutral, and warm up the engine. During this time, pushing passengers can enter the car.

When starting from a tugboat, it is necessary to check the length of the cable, its reliability, and discuss stop signals with the towboat (usually given by a horn).

After a smooth start, the driver of the towed vehicle turns on the ignition (with the clutch depressed), engages second (if necessary, third) gear, and smoothly releases the clutch.

If the engine starts, you give a stop signal, set the speed to “neutral”, and brake smoothly.

If attempts are unsuccessful, the operation can be repeated, especially if the engine showed “signs of life.” If the car does not respond to attempts to start, the reasons may be in the fuel supply systems, which need to be diagnosed in a workshop.

Contraindications for launching from a pusher

Most Western automakers do not prohibit starting a car “from a pusher”, since they are not aware of the existence of such a method. Theory and practice show that mechanical forced starting is harmful to many mechanisms of modern automotive equipment.

For exhaust systems with a catalyst, starting “with a pusher” is harmful because particles of unburned gasoline enter the catalyst. When the fuel ignites in the catalyst, it can become hot, overheat, and lead to an explosion. Experienced drivers, in a desperate situation, try to start with a pusher, but after each attempt they pause to allow the fuel to evaporate.
This method is dangerous for numerous on-board electronics systems that do not like power surges. When the battery is discharged and the engine is forced to start, such surges in electrical loads are inevitable. Shock loads when starting from second or third speed have a bad effect on the timing drive units, leading to chain stretching, timing belt slipping, and cutting off keys.
Starting a cold diesel unit is especially dangerous. When forced to start in diesel engines, the correct relationship between the timing components and the elements of the cylinder-piston group is inevitably disrupted. Incorrect placement of the pistons leads to impacts on the valves. In addition to damage to the valves, rocker arms burst and the cylinder head is deformed. Metal timing chains are partially stretched. In gear drives, damage to the teeth and cases of “cutting” of keys have been noted.
Starting a car “from a pusher” with automatic transmissions is absolutely contraindicated. Manufacturers of modern automatic transmissions prohibit even short-term towing. In automatic transmissions, the oil pump can only operate when the engine is running. When a car is forced to start, there is no connection between the wheels and the engine through the box. The piston group remains motionless, the gearbox gears are subject to critical load and increased wear. Amateurish advice about launching "from a pusher", long-distance transportation in tow can only lead to a major overhaul, a complete replacement of the automatic transmission. In addition, to avoid repairing an automatic transmission, you need to know how to use an automatic transmission.

Video: How to start a car using a cable

The only reasonable alternative to starting a car “from a pusher”, if it is necessary to leave, is to “light it” from another car. This method also has many limitations. Do not light batteries with leaking electrolyte. Batteries that smell strongly (this is a sign of uncontrolled electrolysis) are explosive.

But, if you start the car using a proven cable system, special toothed clamps, and safety rules, starting from a donor battery is less harmful for new imported cars. Particular attention must be paid to correct disconnection. Before removing the wires, reduce the donor's peak load (turn on the headlights, heaters), carefully disconnect the wires, being careful of a short circuit.

Source: http://AvtoMotoProf.ru/v-pomoshh-avtomobilistu/kak-zavesti-avtomobil-s-tolkacha/

How to start a car from a pushrod: when human power decides

Surely there have been times in every driver’s life when it is not possible to start the car on your own. And it is even more likely that in such a situation, drivers wondered how to start the car from a pusher.

It’s good if there is at least one passenger in the car, he will become the main assistant to the hapless helmsman. It’s worse when the driver is left alone with his problem.

However, even in this case there is a way out.

To understand how to start your four-wheeled iron friend from a pusher, let’s consider possible solutions to this issue. So, let's go!

Basic rules for starting a car from a pusher

This procedure must be started if the brakes are fully operational. Still, we are once again looking for a car as a tow or for stronger guys who will agree to push the car.

It is better to agree on a specific stop sign in advance. For example, wave your palm from the window so that your screams are heard by the driver of the towing car. If the battery is not yet completely discharged, you can blink the light or sound the horn.

If the car has a carburetor, then in order to move away, you need to pump up the fuel with the gas pedal. At the same time, you should not overdo it; two to four presses are enough to avoid flooding the candles.

For fuel-injected cars it is better not to do this. Now you can insert the key into the ignition and check that the steering wheel is not locked. It's time to get moving.

The neutral gear is engaged and the command “Pull” (“ Push !”) is given.

So, the car started moving. When it has driven a little and accelerates at neutral speed, you need to squeeze the clutch and engage second (or third) gear. After this, you can begin to slowly release the clutch.

Something like a twitch or jolt will happen (if the car has a carburetor, then you can also lightly press the gas pedal two or three times). As a result, the engine should start (but if the acceleration was weak, then it is likely that the car will not start and you will have to accelerate harder). Next, the clutch is depressed.

Slow down a little if necessary. Neutral speed is activated. All actions are clear and timely, or the driver risks overtaking the towing vehicle.

After all this, a signal is given to the front car (the guys pushing) that it’s time to stop. Once you stop, you should not turn off the car. Let it work for fifteen to twenty minutes. If you fail to start the car the first time, then there is no need to despair. It’s better to try again a couple of times and then the question of how to start a car from a pusher will disappear by itself.

To prevent such an unpleasant situation from happening again the next morning, it is necessary to properly recharge the battery. If it is worn out and discharges quickly, it must be replaced with a new one. If the battery was purchased recently, but quickly discharges after charging, then it is better to send your car for diagnostics. There may be a leak somewhere in the electrical network of your car.

How to push start a car automatically?

An automatic transmission has a lot of “advantages”, but when it comes to towing or emergency starting the engine from a pusher, a lot of questions arise, among which the most popular are: “How to tow a car with an automatic transmission?”, “How to start an automatic transmission from a pusher?” and many others. Today we will try to answer the last question, namely, tell you how to properly start a car with an automatic transmission from a tow or, as motorists say, from a “pusher”.

Almost every driver knows how to start a car with a manual transmission, but not everyone knows how to start an automatic transmission with a pushrod.

Some argue that this should never be done, although in fact such a possibility exists, the question is how to do it correctly.

Of course, there is some truth in the fact that there is little good in starting an automatic transmission from a tug, and it would be wrong to call this procedure completely painless. However, in case of emergency, you can still use this method of starting the engine.

In this part of the article, we will tell you how to properly start a car with an automatic transmission from a tow without causing harm or damaging the transmission of your four-wheeled friend.

1. Connect the tow rope to your car and to the one that will pull you. Set the gear selector to the “N” position. You won’t be able to push a car with an automatic transmission with the help of “heavy guys.”

Do not tow the car down a hill; this will not help it start quickly.

Carburetor and injector - is there a difference?

So, we made sure that we have at our disposal a car that is equipped with a manual transmission. Next, it’s worth checking one more thing. If the starter turns the engine, but it still does not start, then there is no point in pushing the car in an attempt to start it with a pushrod. There is a malfunction of the power unit or lack of fuel.

https://www.youtube.com/watch?v=DLMYdkk0Qj4

It is also worth knowing what kind of car you are driving. The pusher launch algorithm is as follows:

– turn on the car’s ignition to activate all systems;

– depress the clutch and move the gearshift lever to the second or third gear position;

– press the accelerator pedal several times or open the choke slightly (if there is one);

– start setting the car in motion;

– when picking up speed of about 8-10 kilometers per hour, slowly release the clutch pedal;

– as soon as the engine starts, depress the clutch and stop the car, adjusting the speed with the choke or the gas pedal.

This algorithm is suitable if the carburetor is responsible for the distribution of fuel in your car. If your engine has an injector, you should skip the third step. Automation is responsible for triggering the fuel pump in such cars. But remember that after starting the injector should be secured by pressing the accelerator pedal several times.

How to set the car in motion?

Starting a car from a pusher will not be difficult at all if you have a group of close friends on board. A good joke such as the proposal to push the car in connection with the presence of love for walking in it will undoubtedly be appreciated by friends who will enthusiastically get down to business. The matter will be more complicated when you have to start the car alone.

The main thing in such cases is not to try to start the car down the hill, trying to catch it after that and start it. It should be remembered that in some cars the power steering does not work if the car engine is not running. In addition, it may happen that the car that has gained freedom simply cannot be caught up.

In such a situation, to set the car in motion, you can resort to one of the following options:

– roll the car up to a speed of 5 km/h from the driver’s door and try to start it quickly;

– stop a passing car and ask the driver to take it in tow to start the engine.

Then, when you know in advance that the car may not start using the starter, it is better not to take risks and contact the service station without delay.

What are the consequences of starting the engine with a pusher?

For many, launching from a pusher is something like a heroic fun. Of course, for pushing heroes this can be funny, which cannot be said about car valves and timing belts.

It should be understood that any operating conditions of the car that are not specified in its instructions can cause harm to it. And for about half a century this document says nothing about starting the engine from a pusher.

Such actions can lead to the following negative consequences :

– damage to the valves, which will inevitably result in expensive engine repairs;

– damage to clutch discs;

– damage to gearbox gears;

– a broken timing belt and the inability to continue driving.

All of these problems that occur after starting the engine from the pusher cause expensive and not quick repairs. Naturally, such a start will not cause breakdowns in every engine, but such a danger always exists.

To counteract the impact of starting the engine in this manner, use second or third gear. Thanks to this, possible damage to the gearbox is reduced, since impacts are less frequent and softer.

Source: https://auto.today/bok/1913-kak-zavesti-mashinu-s-tolkacha-kogda-chelovecheskaya-sila-reshaet.html

Starting the car from the pushrod

All motorists have encountered a problem associated with a battery that was discharged at the wrong time. And as luck would have it, this happens at a time when it is simply impossible to do without a car. But, probably, everyone knows that you can start a car engine using a pushrod. And now we’ll look at how to do this correctly.

Conditions for successful launch

To start a car from a pusher, you need to invite helpers

First of all, it should be noted that it is not always possible to start the car right away. It is imperative to make sure that all vehicle systems are in working order. In particular: the fuel system, ignition, brakes - all this must be fully functional.

You also need to find one car that will act as a tug in this situation. If this is not possible and the car is on a completely flat surface, then you will have to ask passers-by or other motorists to help you.

Before they start pushing the car, it will be necessary to specify the signals responsible for stopping the car. You can signal with a horn, a hand gesture from the window, or “blinking” headlights.

Checking basic systems before starting

If the car does not start from the starter in the cold season, then first try to warm up the battery. To do this, remove the battery from the car and place it in a room at room temperature.

You will have to wait at least 2-3 hours for the battery to warm up. This will help restore the battery's charge a little, even if you don't have a charger at hand.

After heating, we put the battery in the car and try to start it.

If starting from the battery still fails, then it is necessary to visually inspect the exhaust pipe and check its condition, this is especially important if the car stalled in winter. Under no circumstances should it contain snow, ice, dirt, etc.

Ice signals frozen condensate, so starting the engine in this case will be very difficult. Of course, if you want, you can try to do this; in principle, important parts of the car will not fail.

If there is only snow clogged in the exhaust pipe, just clear it out and there is no need to heat anything.

It is not recommended to start a car if its exhaust pipe is frozen

Also open the hood and inspect the engine compartment. Check that all wires are in place and connected. First of all, this concerns high-voltage wires, otherwise the car will not be able to start either from the pushrod or from the starter, in any way.

Source: http://ktonaavto.ru/avto-faq/prava-i-vozhdenie/zavodim-mashinu-s-tolkacha.html

How to start a car with a pushrod

Quite often, car enthusiasts find themselves in an unpleasant situation when their car does not start on its own due to a dead battery or starter malfunction.

In this situation, the easiest and most proven way to set the car in motion is to start it with a pushrod.

But, despite the prevalence of this method, few people know that if done incorrectly, it can lead to rather dire consequences for the car.

This article describes how to start your car without damaging the engine.

Procedure

In order to start from a pusher, you will need the help of a working car, which will serve as a tow, and a cable. If it is not possible to find another car, then you can use physical force.
It is necessary to agree in advance on the conditioned stop signals - this could be a hand gesture or a sound signal with a horn.
Now get behind the wheel, move the gearshift lever to neutral and turn on the ignition. As soon as the car picks up speed, you should depress the clutch and engage second or third gear. Then smoothly release the clutch while pressing on the gas.
All actions must be performed as clearly and quickly as possible. If you did everything correctly, there will be a fairly sharp push and the engine will start.
Signal to stop to the driver of the towing vehicle or the people pushing you, depress the clutch, engage neutral and brake. After you have started the engine, let it warm up by leaving the car running for a few minutes.

Sometimes it happens that the car does not start the first time. In this case, you need to repeat the above steps until your attempts are successful.
Some motorists recommend that owners of cars with a carburetor fuel supply system press the gas pedal several times while in neutral before engaging the gear.
But you need to know when to stop - 2-3 times is enough, otherwise you can fill the candles with fuel, thereby complicating the task even more.
On cars with an injector, such manipulations should not be carried out.

How to start a car without assistance

If there is no one to help you, and your car is on a slope, you can try to start it alone.

To do this, place the lever in the neutral position and turn on the ignition. Get out of the car and, leaving the driver's door open, push the car while steering.

When the car speed reaches 10 km/h, jump into the driver's seat, depress the clutch, engage second gear, and then, gently pressing the gas pedal, release the clutch.

The engine should start.

Disadvantages of the method

When starting a car and pushing it, there is a high probability of damage to the engine valves as a result of strong shock loads.

The timing belt may also slip or even break, leading to engine breakdown and expensive overhaul.

How to start a car with an automatic transmission

Most motorists are inclined to believe that it is almost impossible to push start a car with an automatic transmission.

This is due to the lack of communication between the engine and transmission in a switched off car.

However, some drivers believe that if, with the help of a tow, they accelerate the car to a speed of about 50 km/h and, holding it at this speed for some time, turn the gearbox to position “D”, then there is a possibility of starting the engine.

It should be noted that in this way it is easier to damage the transmission or get more serious damage than to start the engine. Therefore, if your car has an automatic transmission, you should not resort to this method.

Read also: How to start a car manually

Despite the reliability of modern vehicles, situations still occur when, at the most inopportune moment, your iron horse refuses to start.

Such problems arise especially often in winter at subzero temperatures. However, now you know how to properly start a car using the pushing method.

Source: http://autovogdenie.ru/kak-zavesti-mashinu-s-tolkacha.html

How to properly start a car using a pushrod

Sometimes starting the engine with the usual turn of the ignition key turns out to be impossible due to various technical problems. In such cases, you can try to push start the car.

The procedure requires some physical effort, but as they say, “if you love to ride, you also love to carry a sled.”

Why push the car?

In order to activate a number of mechanisms that start the engine, you need to turn the crankshaft. This task is usually performed by the starter. But if there are certain malfunctions, he turns out to be helpless.

In such cases, you can make the engine work using the towing method. When driving, the drive wheels transmit torque through the transmission to the crankshaft, causing the car to start.

One of the most common reasons for “unconventional” engine starting is a weak battery charge. When the battery current becomes too low, when you turn the ignition key, the usual rhythm of rotation of the crankshaft is replaced by a slower, more “heavy” one.

And when the battery is completely discharged, only small clicks are heard. The ammeter needle on the instrument panel will deviate strongly in the negative direction.

Another possible malfunction is failure of the starter or some component of the ignition system. It is also impossible to exclude a break in the wiring or weak fastening of its contacts. In the latter case, the starter will not react at all to turning the key.

If it is impossible to fix the problem on the spot, then the vehicle will definitely have to be pushed.

Conditions under which you can start a car engine using a pushrod

It is not easy to start the engine in this way alone, so in such situations it is better to resort to outside help.

In order to accelerate a passenger car to the required speed, it will usually take from one to three people (depending on how well the car starts in general). The heavier the vehicle, the more people will be needed to tow it.

Video - Niva started easily from the pusher with the help of 2 people:

In situations where it is difficult to find the required number of pushers, towing the car with another vehicle will help start the engine. In this case, you will need a special cable or an ordinary strong rope, at least three to four meters long.

The success of this event largely depends on the strength of acceleration and the skill of the driver. Some nuances are also influenced by the following factors:

piston group compression;
engine temperature (cold/warm);
condition of the driving wheel tires;
road surface.

Most often, carburetor cars with a manual transmission undergo a similar procedure. Starting their engines is safe and, as a rule, does not cause damage to the engine, which cannot be said about injection and diesel units. It is almost impossible to push start a car with an automatic transmission.

How to properly start a car from a pusher - procedure

At the very beginning, you should turn on the ignition. If the terrain has even the slightest slope (determined visually), then it is more rational to push in its direction.

When the vehicle accelerates to a speed of 10-20 km/h, you need to depress the clutch and engage second gear. Next, smoothly, but without delay, you need to release the pedal. Depending on the adjustment and functioning of the fuel system, you may need to press the gas pedal.

As soon as the car starts, you should put the gear in neutral and, if necessary, warm up the engine to operating temperature.

Video - even a Porsche sometimes has to be started using a pushrod:

In winter, on snowy road sections, you should engage third gear, as the wheels in second may slip. The same technology is used for sandy, soil or gravel surfaces of the route. You can also engage third gear with high cylinder-piston compression or with a complete absence of tread on the tires of the drive wheels.

Many owners of carburetor cars use the “push” method not only in cases of malfunctions, but also in everyday driving. On long descents, in order to save fuel, drivers often engage neutral gear, after which they turn off the engine and let the car coast.

At the end of the inclined section of the road, when the vehicle has reduced its speed to 60 km/h, start the car in the manner described above, using fourth gear.

It is worth noting that such driving is unsafe, since the hydraulic power steering and braking systems do not work when the engine is turned off. It is also important to drive with the ignition on to avoid possible steering lock.

How to start a car alone

If there are not enough people to carry out the required acceleration of the vehicle, then the driver can also take part in the towing process. He will have to run with the left door open, holding the steering wheel with his right hand.

When the vehicle accelerates sufficiently, you need to jump into the cabin while moving and quickly perform a series of the procedures described above (the ignition must be turned on in advance).

Video - how to start a car from a pusher alone:

Using the same method, a driver with good physical training can start a car from a pusher even alone. The main thing is to take into account such features as: the slope of the road, its surface and even wind direction. In traffic-free areas, it is easier to give the car the necessary acceleration by being behind it.

You can start alone in another way. To do this, you need to put the car on the “handbrake” (parking brake), jack up the drive wheel and wrap a strong rope or harness around it (one and a half to two turns).

Having turned on the ignition and second gear, you should pull the cable with a sharp force, forcing the wheel to rotate. If the engine does not start the first time, you must repeat the procedure. If everything works out, you should turn off the gear and lower the jack.

Video - how to start a car using a cable:

This method is more convenient for front-wheel drive cars, where the wheels can be turned by the steering wheel.

Is it possible to start a car with an automatic transmission by towing?

This issue is quite controversial and does not have a clear solution among car enthusiasts. On a stopped car with an automatic transmission, there is no rigid connection between the engine and the wheels.

Therefore, it is impossible to ensure rotation of the crankshaft by towing the vehicle. And since the piston group will remain motionless, it will not be possible to start a car with an automatic transmission from a pusher.

However, there is an opinion that if certain manipulations are performed, it is still possible to start the automatic transmission by towing.

To do this, you need to accelerate the car to 40-50 km/h in the automatic transmission mode “neutral” (N). After driving at this speed for a couple of minutes, the switch should be moved to the “Drive” (D) position, after which the car should start.

But practice shows the opposite and all attempts in most cases ended in failure. A common result of such experiments is failure of the automatic transmission.

Features of starting an injector and diesel engine

Such units should be started from a pusher in the same way as carburetor ones. However, unlike the latter, injectors and diesel engines are more sensitive, so the chance of damage to significant components when towing them is much higher.

When starting a diesel engine using the “push” method, the loads on its gas distribution mechanism are significantly higher than those generated by the starter. And this threatens damage or complete failure of its elements. If, nevertheless, there is an urgent need to start the diesel engine by towing, then this should be done in high gears (3-4).

Injection 8-valve engines can be started from a pusher in the usual way without the risk of causing any damage to it. But for 16-valve engines such procedures are contraindicated. The neutralizer or catalyst may fail. Sometimes there is even a collision of pistons with valves.

Note to the driver

Every vehicle owner should know a few simple rules that can be useful in certain situations and help find a way out of them.

If the battery has at least some charge, then you can slightly ease the fate of the pushers by helping them with the starter.

It is not advisable to stand in front of the exhaust pipe while pushing, as the sudden exhaust can seriously stain your clothes.

It is unsafe to push the vehicle while between it and the trailer (if equipped).

There should always be a tow rope or rope in the trunk.

It is important to remember that push starting an engine is not a normal everyday occurrence. Therefore, it is necessary to quickly identify and eliminate the problem due to which the car does not start in the usual way. After all, any vehicle is created to be ridden, not to be transported with a sled.

Video - how to start a car from a pusher ("Main Road" program):

May be of interest:

Source: http://voditeliauto.ru/sovety-voditelej/kak-zavesti-mashinu-s-tolkacha.html

How to start a car from a pusher: procedure

Hello! Who among us has not been disappointed to discover that the car does not start with the usual turn of the key in the ignition?! Of course, the reasons for this can be completely different, although most often the battery is simply dead. But we will not analyze them in detail now. I want to talk to you about how to start a car from a pushrod, what is needed for this, and what options are available.

Procedure for “revitalizing” a car engine

In order to start a “dead engine”, it is necessary to enlist the help of third parties, because it is very difficult to do this alone.

There is an option for the car to be parked on a slight or steep slope, but this cannot be done if the car is “on automatic”. This starting method can only be done if you have a mechanic.

If there is no slope of the road, then you need to ask any passerby to push the vehicle, or better yet two at once.

So, the algorithm of actions will be approximately as follows:

Turn on the ignition by turning the key. This is necessary so that a spark can be generated, without which the carburetor will not be able to ignite the fuel mixture.
Now we move the gear shift lever to 2nd or 3rd speed. The first gear of the box is not suitable, since in this position the engine resistance is quite high. In addition, in cold weather or on slippery road surfaces, the wheels will simply slip.
We depress the clutch and ask the assistants to push the car. As soon as the speed reaches at least 10–15 kilometers per hour, release the clutch.

If there are no obvious ignition faults, the vehicle will definitely start. Then it’s a matter of technique - we’ll add speed to the throttle and let the car warm up. After this you can start moving.

Other launch options to consider

Is it possible to start in a similar way in reverse gear, novice drivers ask? This is possible in principle, but again in cases where the car is on a slope and will roll down if the brake is released. This is quite problematic to do, so if you were unable to start the engine, it is better to continue the descent until the end of the slope, where you turn the car in the other direction and try to do the same thing in 2nd gear.

https://www.youtube.com/watch?v=B7NyhFr1kfA

How to start a vehicle correctly if there is another car nearby? To do this, we will need to build a tug from a towing rope. The rest of the procedure will be the same.

We tie the cable or fix it in the eyes specially designed for this on the body. The towing vehicle moves off smoothly, accelerates the towed vehicle, the driver of which turns on the ignition and then 3rd gear.

Once the engine is running, you can sound the horn to the driver ahead to stop.

The nuances of injection cars - what is possible and what is not

The injection machine is started in approximately the same way, but with some nuances. If the carburetor allows fuel to be pumped during startup in order to increase speed, then this should not be done immediately on the injector.

The fact is that such cars are equipped with an electronic fuel pump, which itself determines how much and when to supply fuel.

To prevent fuel overflow, we begin to press the accelerator pedal only when the engine has already started running.

In addition, such engines contain more electronics than traditional carburetor engines. Therefore, it is not advisable to start them without a battery or when it is completely discharged.

It is better if at least a minimum percentage of charge is maintained, thanks to which the main devices and electronics can be powered.

Such engines are more sensitive, and in practice there is a risk of damage to main components and systems. The load on the gas distribution mechanism increases during startup.

If 8-valve engines with manual transmission more or less normally accept such a load, then it is undesirable to start 16-valve engines using the indicated methods. Their design is more complex, and breakdowns can be more expensive.

In these cases, it is necessary to call a mechanic and understand the causes of the problems. If we are talking about a discharged battery, then it is better to remove it, charge it at home or in the garage, then put it back in place and only then continue to operate the car. There is another tricky way, shown in the video.

Today we tried to consider the features of starting a car from a pusher, as well as the risks and threats that arise. I recommend checking the blog regularly so as not to miss new materials that are of practical benefit to a wide army of motorists. With this we will say goodbye and see you again!

Sincerely, blog author Andrey Kulpanov

Source: http://avto-kul.ru/ekspluatatsiya-avtomobilya/kak-zavesti-mashinu-s-tolkacha.html

How to start a car using a pushrod

It’s good if there is at least one passenger in the car, he will become the main assistant to the hapless helmsman. It’s worse when the driver is left alone with his problem.

However, even in this case there is a way out.

Method of starting a car from a pusher without assistance

To understand how to start your four-wheeled iron friend from a pusher, let’s consider possible solutions to this issue. So, let's go!

...next to you in difficult times, then he will undoubtedly be able to help set the car in motion. Ask him to push the car from behind, and then take your usual place. Then put it in neutral, start the car and start accelerating it.

When the car starts moving, you need to depress the clutch and, leaving it in the same position, engage second gear. As soon as your car picks up a slight speed, you should slowly release the clutch while lightly pressing on the gas. There will be a small push and the engine will start working.

Depress the clutch again and press the brake pedal, then the car will stop.

Starting the car from a pusher

Ask for help

When a vehicle does not start, and there is not a single living soul near you, another motorist can come to the rescue. In this case, a tow rope is required. In addition, it is very important that the cable is properly secured on both vehicles, as well as certain conditioned stop signals.

Launching from a pusher in this case also has a certain established algorithm. The driver needs to turn on the ignition and select second or third gear, and then squeeze the clutch. After these operations, you need to set both cars in motion. When the cars start to roll, the steering wheel of the towed car must gradually remove their foot from the clutch pedal.

Thus, the engine rotates with the help of the wheels, and this should lead to its starting.

However, this method can have very sad consequences. When starting the engine from a tug, there is a possibility of damage to the valves due to strong shock loads. And in the cold season, the timing belt may slip, which can lead to engine failure and major repairs. Therefore, such an engine plant should be approached only as a last resort.

Starting the car using towing

If it so happens that the driver is faced with a tete-a-tete problem, but the car is on an inclined path at that time, there is a chance to start it without outside help. First you need to turn on neutral and turn the key in the ignition. Make sure there are no passing cars nearby, then open the driver's door and gradually push the car, using one hand to control the steering wheel.

When the car picks up speed up to fifteen kilometers per hour, jump into the seat and squeeze the clutch. Then engage second gear and gradually move your foot away from the clutch, while lightly pressing on the gas. The engine of your car should work. Just remember to constantly monitor the brakes, as there is a high probability of meeting pedestrians, a fence or another car on your way.

In the video you can see how to start a car from a pushrod yourself:

If you have a car with an automatic transmission

It is generally impossible to move a car with an automatic transmission using a pusher . This happens due to the lack of a strong connection between the engine and the transmission. This scheme is equipped with a torque converter, which will not be able to crank the engine when trying to start.

However, some motorists claim that it is still possible to start an automatic transmission from a pushrod.

They are convinced that if they push a car at a speed of forty to fifty kilometers per hour and then turn on the ignition, they will be able to turn on the engine if they keep the car at a constant speed.

But it is unrealistic to bring a car to such a speed using a pusher. And in general, modern cars are not at all inclined to this method.

Most operating manuals for cars with an automatic transmission, especially those aimed at drivers from the countries of the former USSR, warn that attempts to “revive” a car with an automatic transmission from a pusher will lead to irreversible consequences: you will be left without a transmission or without a battery at all. It follows that it is simply unrealistic to drive a car with an automatic transmission.

A modern car is a fairly reliable friend that breaks down very rarely.

However, if a breakdown does occur, the question “is it possible to push start a car” will no longer arise - you are already fully aware and know what to do in such a situation.

Just be sure to go to a car service after the incident to find out the true cause of the breakdown and eliminate it once and for all.

Source: http://365cars.ru/soveti/kak-zavodit-mashinu-s-tolkacha.html